manualshive.com logo in svg

Holtek HT32F50231, Руководство пользователя, Страница: 308 / 486

Поделиться
Скачать
Holtek HT32F50231 Скачать руководство пользователя страница 308

Rev. 1.00 

308 of 486

July 31, 2018

32-Bit Arm

®

 Cortex

®

-M0+ MCU

HT32F50231/HT32F50241

16  Motor Control T

imer (MCTM)

16  Motor Control T

imer (MCTM)

Channel Controller

The MCTM has four independent channels which can be used as capture inputs or compare match 

outputs. Each capture input or compare match output channel is composed of a preload register 

and a shadow register. Data access of the APB bus is always implemented by reading/writing the 

preload register.

When used in the input capture mode, the counter value is captured into the CHxCCR shadow 

register first and then transferred into the CHxCCR preload register when the capture event occurs.

When used in the compare match output mode, the contents of the CHxCCR preload register is copied 

into the associated shadow register, the counter value is then compared with the register value.

CHxCCR 

(Preload Register)

CHxCCR 

(Shadow Register)

APB Bus Interface

Capture 

Controller

Capture

Capture Transfer

Compare 

Controller

Compare Transfer

Read CHxCCR 

CHxCCS

CHxCCS

CHxCCG

CHxPRE

CHxE

CHxPSC

Write CHxCCR 

Update Event 1

CHxCCR 
TM_CNT

Figure 106.  Capture/Compare Block Diagram

Capture Counter Value Transferred to CHxCCR

When the channel is used as a capture input, the counter value is captured into the Channel 

Capture/Compare Register (CHxCCR) when an effective input signal transition occurs. Once the 

capture event occurs, the CHxCCIF flag in the INTSR register is set accordingly. If the CHxCCIF 

bit is already set, i.e., the flag has not yet been cleared by software, and another capture event on 

this channel occurs, the corresponding channel Over-Capture flag, named CHxOCF, will be set.

25

26

27

28

29

30

31

32

33

34

35

0

26

32

CNTR

CHxCCR

CHxCCIF

CHxOCF

MT_CH0

(TI0)

Figure 107.  Input Capture Mode

Содержание HT32F50231







































































































































































































































































































































































































































































































Отзывы:

Нет отзывов