manualshive.com logo in svg

Holtek HT32F50231, Руководство пользователя, Страница: 34 / 486

Поделиться
Скачать
Holtek HT32F50231 Скачать руководство пользователя страница 34

Rev. 1.00 

34 of 486

July 31, 2018

32-Bit Arm

®

 Cortex

®

-M0+ MCU

HT32F50231/HT32F50241

3  System 

Architecture

4  Flash Memory Controller (FMC)

4 

 Flash Memory Controller (FMC)

Introduction

The Flash Memory Controller, FMC, provides functions of flash operation and pre-fetch buffer 

for the embedded on-chip Flash memory. Figure below shows the block diagram of FMC which 

includes programming interface, control register, pre-fetch buffer and access interface. Since the 

access speed of Flash memory is slower than the CPU, a wide access interface with pre-fetch buffer 

is provided to the Flash memory in order to reduce the CPU wait state, which will cause instruction 

gaps. The functions of word programming / page erase are also provided for instruction / data 

storage of Flash memory.

Flash Memory Controller

Main Flash 

Memory

Information 

Block 

Wait State 

Control

Addressing

Data

Programming

Control

Control Register

Pre-fetch Buffer

System Bus

AHB 

Peripheral 

Bus

Flash

Figure 5.  Flash Memory Controller Block Diagram

Features

 

▄

Up to 64 KB of on-chip Flash memory for storing instruction / data and option bytes

 

●

64 KB (instruction / data + Option Byte)

 

●

32 KB (instruction / data + Option Byte)

 

▄

Page size of 1 KB, totally up to 64 pages depending on the main Flash size

 

▄

Wide access interface with pre-fetch buffer to reduce instruction gaps

 

▄

Page erase and mass erase capability

 

▄

32-bit word programming

 

▄

Interrupt capability when ready or error occurs

 

▄

Flash read protection to prevent illegal code / data access

 

▄

Page erase / program protection to prevent unexpected operation

Содержание HT32F50231







































































































































































































































































































































































































































































































Отзывы:

Нет отзывов