Harmonic Drive HA-680 Series Скачать руководство пользователя | Manualshive

Страница: 17 / 138

background image

Chapter 1

Outlines of the HA-680 driver

-

11

-

1-9

LED display

The 2 LEDs (green and red) indicate the state of the HA-680 driver.

State

LED green

LED red

Remarks

Control power ON

ON

OFF

The connected actuator and the actuator set to

the driver are different.

Blinking

OFF

Servo-ON

ON

ON

Alarm (*1)

ON

Blinking

The number of times it blinks varies

depending on the alarm. Refer to 1-10.

CPU error

Blinking

Blinking

The green and red LEDs blink alternately.

*1 If two or more alarms occur, only the latest alarm is displayed.

1-10

Outline of protective functions

The HA-680 driver has various types of protection function. When an error occurs in the system, it

immediately turns off the servo, and outputs an “alarm” signal to the host device.
When these protection functions trip, driving of the actuator is stopped (the motor becomes servo-off),

and the display LED blinks at 0.5-second intervals. (It illuminates in green and blinks in red: The number

of times it blinks varies depending on the alarm. See below.)
If two or more alarms occur, only the latest alarm is displayed. Up to 8 latest alarms are recorded.

Recorded alarms can be checked with “Alarm History” of dedicated communication software PSF-520.

Alarm code

Description

No. of times

LED blinks

Releasing

Overload

Electronic thermal detected an overload state.

1

Available *1

Deviation counter

overflow

The value of the deviation counter exceeded the parameter

setting value.

2

Available *1

Encoder break

detection

The encoder line was broken.

3

Not available *2

Encoder reception

error

Serial encoder data could not be received 10 times in a row.

4

Not available *2

Serial encoder data could not be received over an extended time

period, and encoder monitor could not be outputted successfully.

5

UVW error

All UVW signals of the encoder became the same level.

6

Not available *2

Regenerative error

The main circuit voltage detection circuit detected overvoltage.

7

Not available *2

Operation

temperature error

The temperature of the HA-680 main unit tripped the temperature

rise sensor.

8

Not available *2

System error

An error of the current detection circuit was detected.

9

Not available *2

Overcurrent

The current detection circuit detected excessive current.

10

Not available *2

Load short circuit

Excessive current flowed through the FET.

11

Not available *2

Memory error

Read/write of EEPROM failed.

12

Not available *2

Overspeed

The motor axis speed exceeded the maximum rotation speed

+100 rpm for 0.5 s or longer.

13

Not available *2

*1 The servo does not turn on unless the S-ON signal is entered again after the alarm is cleared with the

CLR signal.

*2: Shut off the power supply after remedying a cause of the alarm that releasing is impossible. Then

turn on the power supply.

«
...
15
16
17
18
19
...
»

Содержание HA-680 Series











































































































































Отзывы:

Нет отзывов

Похожие инструкции для HA-680 Series

Бренд: SAJ Страницы: 59

Бренд: Eaton Страницы: 12

Бренд: DVS Страницы: 16

Бренд: hager Страницы: 4

Бренд: sauter Страницы: 8

Бренд: HDT Страницы: 130

Atrium HS Comfort drive

Бренд: Maco Страницы: 64

FC 300 Interbus

Бренд: Danfoss Страницы: 45

FC 300 Profibus

Бренд: Danfoss Страницы: 85

Бренд: Danfoss Страницы: 16

VLT Brake Resistor MCE 101

Бренд: Danfoss Страницы: 146

Бренд: Antal Страницы: 12

Бренд: ABB Страницы: 2

Impulse G+ series 4

Бренд: Magnetek Страницы: 3

VLT Panduan Cepat

Бренд: Danfoss Страницы: 25

HYDROVAR Watercooled

Бренд: Xylem Страницы: 68

Бренд: YASKAWA Страницы: 102

Бренд: ABB Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды