Harmonic Drive HA-680 Series Скачать руководство пользователя

Страница: 90 / 138

Chapter 6 Setting up parameters

09: Step correction switch range

(position)

●

Function

This parameter specifies the amount of position deviation for the deviation counter where the following

will take effect: speed step correction ([Parameter]

⇒

[07: Speed step correction]) and torque step

correction ([Parameter]

⇒

[08: Torque step correction]).

The values of “Speed step correction” and “Torque step correction” become effective when the amount

of position deviation becomes bigger than those set values.

●

Setting

unit

Lower limit

Upper limit

Default

Pulse

9999

4000

Note: For ordinary use, leave this parameter unchanged from 0.

10: Control mode

(The power must be turned on again after setting a change.)

(position / speed / torque)

●

Function

The HA-680 driver can control the actuator in either the [position control], [speed control] or [torque

control]. This function selects an operating mode.
In the position control a command signal is composed of pulse trains, while in the speed mode or torque

mode it is composed of an analog voltage.
[0]: position control (factory default) [1]: speed control [2]: torque control

●

Setting

unit

Lower limit

Upper limit

Default

Note 1: The power must be turned on again after setting a change. The previous value is effective until

you turn on the power again.

Note 2: The upper limit value is 5. However, do not use setting values 3, 4, and 5 because these are

reserved for the system.

Содержание HA-680 Series











































































































































Результаты поиска

Содержание HA-680 Series

Отзывы:

Похожие инструкции для HA-680 Series

Бренды по названию

Популярные бренды

Harmonic Drive HA-680 Series, Руководство пользователя

Результаты поиска

Содержание HA-680 Series

Отзывы:

Похожие инструкции для HA-680 Series

Бренды по названию

Популярные бренды