Harmonic Drive HA-680 Series Скачать руководство пользователя

Страница: 104 / 138

Chapter 6 Setting up parameters

39: Reserved for the system

This parameter is reserved for the system. Do not change the setting.

40: Internal command input factor

(torque)

●

Function

“Internal torque command value” allows you to operate the actuator without an input signal. It is useful

for a test run of the actuator alone and for system diagnosis. The command value can be set here.
For operation of the actuator using “internal command,” internal commands are selected when a signal

is entered (on) to “CN2 Internal/external command: CMD-CHG.” External commands are selected when

a signal is turned off.
To rotate the actuator in the reverse direction with this “internal speed command value,” turn on “CN2

REV enable: REV-EN.”

●

Setting

unit

Lower limit

Upper limit

Default

note

Note: The setting value varies depending on the model of the actuator. The upper limit value is

calculated using the following formula based on the values listed in the catalogue and manual of

the AC servo actuator.

The allowable continuous torque is 100%.

Maximum current

Allowable continuous current

100 (%) = upper limit (%)

41: Torque command input factor

(torque)

●

Function

This function sets the output torque when the input command voltage is 10 V.

●

Setting

unit

Lower limit

Upper limit

Default

note

Note: The setting value varies depending on the model of the actuator. The upper limit value is

calculated using the following formula based on the values listed in the catalogue and manual of

the AC servo actuator.

The allowable continuous torque is 100%.

Maximum current

Allowable continuous current

100 (%) = upper limit (%)

Output current = Allowable continuous current

Torque command input factor

100

Command voltage factor

100

Содержание HA-680 Series











































































































































Результаты поиска

Содержание HA-680 Series

Отзывы:

Похожие инструкции для HA-680 Series

Бренды по названию

Популярные бренды

Harmonic Drive HA-680 Series, Руководство пользователя

Результаты поиска

Содержание HA-680 Series

Отзывы:

Похожие инструкции для HA-680 Series

Бренды по названию

Популярные бренды