Hanwha Techwin Wisenet PRN-4011 Скачать руководство пользователя страница 36

Страница: 36 / 88

raid mode setting

Click on the <

use

> or <

Setup

> button.

In the use RAID window, select settings of RAID and click on the <

> button.

•

Use/Not Used : You can select whether or not to use the RAID mode.

•

Shows the RAID types supported by each product.

Product

RAID type

PRN-4011

Level 5, level 6

XRN-2011

Level 5

XRN-811S

Level 1

It will show the list of HDDs that compose a RAID. In the RAID screen, click on <

The data deletion and system rebooting message window will appear. You can click on the <

> button to

reboot the system for RAID mode setting.

When RAID building is complete, select <

Setup

> - <

device

> - <

Storage device

> - <

raid

> to check the

build.

If you disable the RAID mode at RAID level 5 or 6, then every RAID array will be canceled. If you want to cancel only one of

RAID arrays in use, then go to the setup window and disable that specific RAID array.

If the status of HDD is displayed as inspected/replaced in the device/format page, you cannot use it to build a RAID.

When the RAID mode is in use, it is recommended to use HDDs with the same storage space from the same manufacturer.

If you enable or disable the RAID mode, existing data will be deleted. You make sure to backup your data.

RAID Array capacity calculation

When you build the RAID in level 5, the available capacity of a RAID is (the least HDD capacity) x (total number of HDDs -1).

When you build the RAID in level 6, the available capacity of a RAID is (the least HDD capacity) x (total number of HDDs -2).

If you use HDDs with different capacity, the HDD with the smallest capacity will be used to build a RAID.

recovering raid array

If the HDD number whose <

Status

> is shown as Faulty or Check is recognized, check the location of HDD

to be replaced on the HDD map.

Replace the malfunctioning HDD from the NVR with a new HDD.

When recovery starts, the LED for the replaced HDD will blink in orange.

In the "

device

Storage device

raid

" menu, you can check the recovery progress. (Only PRN-4011

supports RAID LED.)

Replace it with the same model of HDD or an HDD of the same capacity from the same manufacturer.

A HDD used to build the RAID should be one of the recommended models.

If it's not possible to use the same model of HDD, then use the HDD with the same capacity from the same manufacturer

should be used.

If you remove the power cord while using the RAID, it can damage it, so be careful.

For reliable power, it is recommended you use the UPS.

A new HDD to be replaced should be one that is not RAID configured.

36_

menu setup

Содержание Wisenet PRN-4011

























































































Результаты поиска

Содержание Wisenet PRN-4011

Отзывы:

Похожие инструкции для Wisenet PRN-4011

Бренды по названию

Популярные бренды

Hanwha Techwin Wisenet PRN-4011, Руководство пользователя

Результаты поиска

Содержание Wisenet PRN-4011

Отзывы:

Похожие инструкции для Wisenet PRN-4011

Бренды по названию

Популярные бренды