Hanwha Techwin Wisenet PRN-4011 Скачать руководство пользователя страница 35

Страница: 35 / 88

menu > device > Storage device > raid

•

RAID status : Displays the operational status of the RAID.

- Active : Signals the fact that the RAID is operating normally.
- Degraded : It is displayed when the one or more HDDs that make up the RAID are malfunctioning. When

the maximum number of HDDs allowed in the RAID level are malfunctioning, if an additional HDD

malfunctions, you cannot use or restore the RAID.

Immediately, replace the HDD and proceed with restoration.

For more information about how to replace the HDD and recover the RAID array, see the "

Recovering RAID Array

" page under

Menu Setup

Setting the Device

" in the Table of Contents.

- Rebuilding : Rebuilding: Indicates that the RAID array is in the recovery process. At RAID level 5 or 6, if the

max number of HDDs allowed by the RAID level is malfunctioning, and one more HDD caused malfunction

during rebuilding, then you cannot recover or use the RAID array.

- Fail : This means that the RAID cannot be used or restored.

•

Disk status : Displays the current operating condition of the HDDs installed in a RAID.

- Active : Displays that the HDD is operating normally.
- Faulty : It displays that the HDD is malfunctioning. You need to immediately replace the HDD for smooth

recovery of the RAID.

- Check : A problem occurs on the HDD, requiring replacement or inspection.
- Ready : If recovery of 2 HDDs is required in the RAID 6 state, HDDs for which rebuild is pending are

displayed.

•

Capacity : It shows the total capacity of the HDDs that composes a RAID.

•

Temperature : You can check the temperature of HDD(s) that compose a RAID.

raid mode setting

This function is only available for products that support RAID. To find products that support RAID, see “

nvr

products supporting each feature

”. (Product Specification Manual, page 4)

If you enable the RAID (Redundant Array of Independent Disks) mode, you can safely recover your data even if

your system HDD is damaged.

•

raid for each product

Product

RAID type

XRN-2011

RAID level 5 is supported.

RAID level 5: You can recover the operation and data of only one malfunctioning HDD out of all the HDDs

in the RAID array.

PRN-4011

RAID level 5 and 6 are supported.

RAID level 5: You can recover the operation and data of only one malfunctioning HDD out of all the HDDs

in the RAID array."

RAID level 6: You can recover the operation and data of two malfunctioning HDDs out of all the HDDs in

the RAID array.

You can configure two arrays of RAIDs for the product. The first RAID array only uses HDDs mounted in

Slot 1 to 6 while the second RAID array only uses HDDs mounted in Slot 7 to 12.

You can configure an RAID array when the RAID array to be configured has 5 to 6 HDDs mounted in it.

RAID level 6 is available only if one RAID array has 6 HDDs mounted in it.

XRN-811S

RAID level 1 is supported.
RAID level 1: Maintains the same data in two HDDs consisting an RAID array. So, even if one fails, you

can still use the data from the other and recover it.

When you set RAID for individual HDDs, the "

HDD connection status changed.

” message will pop up along with a beeping

sound, and this is normal.

When configuring RAID, NVR was expecting five or more individual HDDs. But the number of HDDs is reduced as the

RAID is configured. This does not cause any problem to NVR recording and the use of RAID and HDDs.

Even for general HDDs, the number is often reduced while using, and it does not cause any problem to NVR recording

and the use of HDDs.

English

_35

● menu

Setup

Содержание Wisenet PRN-4011

























































































Результаты поиска

Содержание Wisenet PRN-4011

Отзывы:

Похожие инструкции для Wisenet PRN-4011

Бренды по названию

Популярные бренды

Hanwha Techwin Wisenet PRN-4011, Руководство пользователя

Результаты поиска

Содержание Wisenet PRN-4011

Отзывы:

Похожие инструкции для Wisenet PRN-4011

Бренды по названию

Популярные бренды