H3C S5500-SI Series Скачать руководство пользователя

Страница: 92 / 130

5-31

[DeviceC-GigabitEthernet1/0/3] undo stp enable

[DeviceC-GigabitEthernet1/0/3] port link-type trunk

[DeviceC-GigabitEthernet1/0/3] port trunk permit vlan 20

[DeviceC-GigabitEthernet1/0/3] qos trust dot1p

[DeviceC-GigabitEthernet1/0/3] quit

# Disable physical state change suppression and STP on GigabitEthernet 1/0/4, configure the

port as a trunk port, and assign it to VLAN 10, and configure it to trust the 802.1p precedence of

the received packets.

[DeviceC] interface gigabitethernet 1/0/4

[DeviceC-GigabitEthernet1/0/4] undo link-delay

[DeviceC-GigabitEthernet1/0/4] undo stp enable

[DeviceC-GigabitEthernet1/0/4] port link-type trunk

[DeviceC-GigabitEthernet1/0/4] port trunk permit vlan 10

[DeviceC-GigabitEthernet1/0/4] qos trust dot1p

[DeviceC-GigabitEthernet1/0/4] quit

# Create RRPP domain 1, configure VLAN 10 as the primary control VLAN of RRPP domain 1,

and configure the VLAN mapped to MSTI 1 as the protected VLAN of RRPP domain 1.

[DeviceC] rrpp domain 1

[DeviceC-rrpp-domain1] control-vlan 100

[DeviceC-rrpp-domain1] protected-vlan reference-instance 1

# Configure Device C as the transit node of primary ring 1 in RRPP domain 1, with

GigabitEthernet 1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port, and

enable ring 1.

[DeviceC-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 1/0/1

secondary-port gigabitethernet 1/0/2 level 0

[DeviceC-rrpp-domain1] ring 1 enable

# Configure Device C as the edge node of subring 3 in RRPP domain 1, with GigabitEthernet

1/0/4 as the edge port, and enable subring 3.

[DeviceC-rrpp-domain1] ring 3 node-mode edge edge-port gigabitethernet 1/0/4

[DeviceC-rrpp-domain1] ring 3 enable

[DeviceC-rrpp-domain1] quit

# Create RRPP domain 2, configure VLAN 105 as the primary control VLAN of RRPP domain 2,

and configure the VLAN mapped to MSTI 2 as the protected VLAN of RRPP domain 2.

[DeviceC] rrpp domain 2

[DeviceC-rrpp-domain2] control-vlan 105

[DeviceC-rrpp-domain2] protected-vlan reference-instance 2

# Configure Device C as the transit node of primary ring 1 in RRPP domain 2, with

GigabitEthernet 1/0/1 as the primary port and GigabitEthernet 1/0/2 as the secondary port, and

enable ring 1.

[DeviceC-rrpp-domain2] ring 1 node-mode transit primary-port gigabitethernet 1/0/1

secondary-port gigabitethernet 1/0/2 level 0

[DeviceC-rrpp-domain2] ring 1 enable

# Configure Device C as the edge node of subring 2 in RRPP domain 2, with GigabitEthernet

1/0/3 as the edge port, and enable subring 2.

[DeviceC-rrpp-domain2] ring 2 node-mode edge edge-port gigabitethernet 1/0/3

[DeviceC-rrpp-domain2] ring 2 enable

[DeviceC-rrpp-domain2] quit

# Enable RRPP.

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды