H3C S5500-SI Series Скачать руководство пользователя

Страница: 75 / 130

5-14

For more information about the

port link-type trunk

and

port trunk permit vlan

commands, see

VLAN Configuration Commands

in the

Layer 2 - LAN Switching Command

Reference

For more information about the

undo stp enable

command, see

MSTP Configuration

Commands

in the

Layer 2 - LAN Switching Command Reference

The 802.1p priority of trusted packets on the RRPP ports must be configured, so that RRPP

packets take higher precedence than data packets when passing through the RRPP ports.

For more information about the

qos trust

dot1p

command, see

Priority Mapping

Configuration Commands

in the

ACL and QoS Command Reference

Do not enable OAM remote loopback function on an RRPP port. Otherwise, this may cause

temporary broadcast storm.

You are recommended not to configure physical-link-state change suppression time on a

port accessing an RRPP ring to accelerate topology convergence. For more information,

see

undo link-delay

command

Ethernet Interface Configuration Commands

in the

Layer

2 - LAN Switching Command Reference

Configuring RRPP Nodes

The maximum number of rings that can be configured on a device in all RRPP domains is

16.

If a device carries multiple RRPP rings in an RRPP domain, only one ring can be

configured as the primary ring on the device and the role of the device on a subring can

only be an edge node or an assistant-edge node.

Specifying a master node

Perform this configuration on a device to be configured as a master node.

Follow these steps to specify a master node:

To do…

Use the command…

Remarks

Enter system view

system-view

—

Enter RRPP domain view

rrpp domain domain-id

—

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды