H3C S5500-SI Series Скачать руководство пользователя

Страница: 91 / 130

5-30

[DeviceB-rrpp-domain2] protected-vlan reference-instance 2

# Configure Device B as the transit node of primary ring 1, with GigabitEthernet 1/0/1 as the

primary port and GigabitEthernet 1/0/2 as the secondary port, and enable ring 1.

[DeviceB-rrpp-domain2] ring 1 node-mode transit primary-port gigabitethernet 1/0/1

secondary-port gigabitethernet 1/0/2 level 0

[DeviceB-rrpp-domain2] ring 1 enable

# Configure Device B as the assistant-edge node of subring 2 in RRPP domain 2, with

GigabitEthernet 1/0/3 as the edge port, and enable subring 2.

[DeviceB-rrpp-domain2] ring 2 node-mode assistant-edge edge-port gigabitethernet 1/0/3

[DeviceB-rrpp-domain2] ring 2 enable

[DeviceB-rrpp-domain2] quit

# Enable RRPP.

[DeviceB] rrpp enable

3) Configuration on Device C

# Create VLANs 10 and 20, map VLAN 10 to MSTI 1 and VLAN 20 to MSTI 2, and activate MST

region configuration.

<DeviceC> system-view

[DeviceC] vlan 10

[DeviceC-vlan10] quit

[DeviceC] vlan 20

[DeviceC-vlan20] quit

[DeviceC] stp region-configuration

[DeviceC-mst-region] instance 1 vlan 10

[DeviceC-mst-region] instance 2 vlan 20

[DeviceC-mst-region] active region-configuration

[DeviceC-mst-region] quit

# Disable physical state change suppression and STP on GigabitEthernet 1/0/1 and

GigabitEthernet 1/0/2, configure the two ports as trunk ports, and assign them to VLAN 10 and

VLAN 20, and configure them to trust the 802.1p precedence of the received packets.

[DeviceC] interface gigabitethernet 1/0/1

[DeviceC-GigabitEthernet1/0/1] undo link-delay

[DeviceC-GigabitEthernet1/0/1] undo stp enable

[DeviceC-GigabitEthernet1/0/1] port link-type trunk

[DeviceC-GigabitEthernet1/0/1] port trunk permit vlan 10 20

[DeviceC-GigabitEthernet1/0/1] qos trust dot1p

[DeviceC-GigabitEthernet1/0/1] quit

[DeviceC] interface gigabitethernet 1/0/2

[DeviceC-GigabitEthernet1/0/2] undo link-delay

[DeviceC-GigabitEthernet1/0/2] undo stp enable

[DeviceC-GigabitEthernet1/0/2] port link-type trunk

[DeviceC-GigabitEthernet1/0/2] port trunk permit vlan 10 20

[DeviceC-GigabitEthernet1/0/2] qos trust dot1p

[DeviceC-GigabitEthernet1/0/2] quit

# Disable physical state change suppression and STP on GigabitEthernet 1/0/3, configure the

port as a trunk port, and assign it to VLAN 20, and configure it to trust the 802.1p precedence of

the received packets.

[DeviceC] interface gigabitethernet 1/0/3

[DeviceC-GigabitEthernet1/0/3] undo link-delay

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды