H3C S5500-SI Series Скачать руководство пользователя

Страница: 84 / 130

5-23

[DeviceA] rrpp enable

2) Configuration on Device B

# Disable physical state change suppression and STP on GigabitEthernet 1/0/1,

GigabitEthernet 1/0/2, and GigabitEthernet 1/0/3, configure the ports as trunk ports, and assign

them to all VLANs, and configure them to trust the 802.1p precedence of the received packets.

<DeviceB> system-view

[DeviceB] interface gigabitethernet 1/0/1

[DeviceB-GigabitEthernet1/0/1] undo link-delay

[DeviceB-GigabitEthernet1/0/1] undo stp enable

[DeviceB-GigabitEthernet1/0/1] port link-type trunk

[DeviceB-GigabitEthernet1/0/1] port trunk permit vlan all

[DeviceB-GigabitEthernet1/0/1] qos trust dot1p

[DeviceB-GigabitEthernet1/0/1] quit

[DeviceB] interface gigabitethernet 1/0/2

[DeviceB-GigabitEthernet1/0/2] undo link-delay

[DeviceB-GigabitEthernet1/0/2] undo stp enable

[DeviceB-GigabitEthernet1/0/2] port link-type trunk

[DeviceB-GigabitEthernet1/0/2] port trunk permit vlan all

[DeviceB-GigabitEthernet1/0/2] qos trust dot1p

[DeviceB-GigabitEthernet1/0/2] quit

[DeviceB] interface gigabitethernet 1/0/3

[DeviceB-GigabitEthernet1/0/3] undo link-delay

[DeviceB-GigabitEthernet1/0/3] undo stp enable

[DeviceB-GigabitEthernet1/0/3] port link-type trunk

[DeviceB-GigabitEthernet1/0/3] port trunk permit vlan all

[DeviceB-GigabitEthernet1/0/3] qos trust dot1p

[DeviceB-GigabitEthernet1/0/3] quit

# Create RRPP domain 1, configure VLAN 4092 as the primary control VLAN of RRPP domain 1,

and configure the VLANs mapped to MSTIs 0 through 16 as the protected VLANs of RRPP

domain 1.

[DeviceB] rrpp domain 1

[DeviceB-rrpp-domain1] control-vlan 4092

[DeviceB-rrpp-domain1] protected-vlan reference-instance 0 to 16

# Configure Device B as a transit node of primary ring 1, with GigabitEthernet 1/0/1 as the

primary port and GigabitEthernet 1/0/2 as the secondary port, and enable ring 1.

[DeviceB-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 1/0/1

secondary-port gigabitethernet 1/0/2 level 0

[DeviceB-rrpp-domain1] ring 1 enable

# Configure Device B as the edge node of subring 2, with GigabitEthernet 1/0/3 as the edge

port, and enable ring 2.

[DeviceB-rrpp-domain1] ring 2 node-mode edge edge-port gigabitethernet 1/0/3

[DeviceB-rrpp-domain1] ring 2 enable

[DeviceB-rrpp-domain1] quit

# Enable RRPP.

[DeviceB] rrpp enable

3) Configuration on Device C

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды