H3C S5500-SI Series Скачать руководство пользователя

Страница: 110 / 130

6-49

[DeviceC-smlk-group-1] flush enable control-vlan 10

[DeviceC-smlk-group-1] quit

# Create smart link group 2, and configure all VLANs mapped to MSTI 2 as the protected VLANs for

smart link group 2.

[DeviceC] smart-link group 2

[DeviceC-smlk-group2] protected-vlan reference-instance 2

# Configure GigabitEthernet 1/0/1 as the slave port and GigabitEthernet 1/0/2 as the master port for

smart link group 2.

[DeviceC-smlk-group2] port gigabitethernet 1/0/2 master

[DeviceC-smlk-group2] port gigabitethernet 1/0/1 slave

# Enable role preemption in smart link group 2, enable flush message sending, and configure VLAN

101 as the transmit control VLAN.

[DeviceC-smlk-group2] preemption mode role

[DeviceC-smlk-group2] flush enable control-vlan 101

[DeviceC-smlk-group2] quit

2) Configuration on Device B

# Create VLAN 1 through VLAN 200.

<DeviceB> system-view

[DeviceB] vlan 1 to 200

# Configure GigabitEthernet 1/0/1 and GigabitEthernet 1/0/2 as trunk ports and assign them to VLANs

1 through 200; enable flush message receiving on GigabitEthernet 1/0/1 and GigabitEthernet 1/0/2

and configure VLAN 10 and VLAN 101 as the receive control VLANs.

[DeviceB] interface gigabitethernet 1/0/1

[DeviceB-GigabitEthernet1/0/1] port link-type trunk

[DeviceB-GigabitEthernet1/0/1] port trunk permit vlan 1 to 200

[DeviceB-GigabitEthernet1/0/1] smart-link flush enable control-vlan 10 101

[DeviceB-GigabitEthernet1/0/1] quit

[DeviceB] interface gigabitethernet 1/0/2

[DeviceB-GigabitEthernet1/0/2] port link-type trunk

[DeviceB-GigabitEthernet1/0/2] port trunk permit vlan 1 to 200

[DeviceB-GigabitEthernet1/0/2] smart-link flush enable control-vlan 10 101

[DeviceB-GigabitEthernet1/0/2] quit

3) Configuration on Device D

# Create VLAN 1 through VLAN 200.

<DeviceD> system-view

[DeviceD] vlan 1 to 200

# Configure GigabitEthernet 1/0/1 and GigabitEthernet 1/0/2 as trunk ports and assign them to VLANs

1 through 200; enable flush message receiving on GigabitEthernet 1/0/1 and GigabitEthernet 1/0/2

and configure VLAN 10 and VLAN 101 as the receive control VLANs.

[DeviceD] interface gigabitethernet 1/0/1

[DeviceD-GigabitEthernet1/0/1] port link-type trunk

[DeviceD-GigabitEthernet1/0/1] port trunk permit vlan 1 to 200

[DeviceD-GigabitEthernet1/0/1] smart-link flush enable control-vlan 10 101

[DeviceD-GigabitEthernet1/0/1] quit

[DeviceD] interface gigabitethernet 1/0/2

[DeviceD-GigabitEthernet1/0/2] port link-type trunk

[DeviceD-GigabitEthernet1/0/2] port trunk permit vlan 1 to 200

[DeviceD-GigabitEthernet1/0/2] smart-link flush enable control-vlan 10 101

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды