H3C S5500-SI Series Скачать руководство пользователя

Страница: 89 / 130

5-28

[DeviceA-GigabitEthernet1/0/2] qos trust dot1p

[DeviceA-GigabitEthernet1/0/2] quit

# Create RRPP domain 1, configure VLAN 100 as the primary control VLAN of RRPP domain 1,

and configure the VLAN mapped to MSTI 1 as the protected VLAN of RRPP domain 1.

[DeviceA] rrpp domain 1

[DeviceA-rrpp-domain1] control-vlan 100

[DeviceA-rrpp-domain1] protected-vlan reference-instance 1

# Configure Device A as the master node of primary ring 1, with GigabitEthernet 1/0/1 as the

primary port and GigabitEthernet 1/0/2 as the secondary port, and enable ring 1.

[DeviceA-rrpp-domain1] ring 1 node-mode master primary-port gigabitethernet 1/0/1

secondary-port gigabitethernet 1/0/2 level 0

[DeviceA-rrpp-domain1] ring 1 enable

[DeviceA-rrpp-domain1] quit

# Create RRPP domain 2, configure VLAN 105 as the primary control VLAN of RRPP domain 2,

and configure the VLAN mapped to MSTI 2 as the protected VLAN of RRPP domain 2.

[DeviceA] rrpp domain 2

[DeviceA-rrpp-domain2] control-vlan 105

[DeviceA-rrpp-domain2] protected-vlan reference-instance 2

# Configure Device A as the master node of primary ring 1, with GigabitEthernet 1/0/2 as the

master port and GigabitEthernet 1/0/1 as the secondary port, and enable ring 1.

[DeviceA-rrpp-domain2] ring 1 node-mode master primary-port gigabitethernet 1/0/2

secondary-port gigabitethernet 1/0/1 level 0

[DeviceA-rrpp-domain2] ring 1 enable

[DeviceA-rrpp-domain2] quit

# Enable RRPP.

[DeviceA] rrpp enable

2) Configuration on Device B

# Create VLANs 10 and 20, map VLAN 10 to MSTI 1 and VLAN 20 to MSTI 2, and activate MST

region configuration.

<DeviceB> system-view

[DeviceB] vlan 10

[DeviceB-vlan10] quit

[DeviceB] vlan 20

[DeviceB-vlan20] quit

[DeviceB] stp region-configuration

[DeviceB-mst-region] instance 1 vlan 10

[DeviceB-mst-region] instance 2 vlan 20

[DeviceB-mst-region] active region-configuration

[DeviceB-mst-region] quit

# Disable physical state change suppression and STP on GigabitEthernet 1/0/1 and

GigabitEthernet 1/0/2, configure the two ports as trunk ports, and assign them to VLAN 10 and

VLAN 20, and configure them to trust the 802.1p precedence of the received packets.

[DeviceB] interface gigabitethernet 1/0/1

[DeviceB-GigabitEthernet1/0/1] undo link-delay

[DeviceB-GigabitEthernet1/0/1] undo stp enable

[DeviceB-GigabitEthernet1/0/1] port link-type trunk

[DeviceB-GigabitEthernet1/0/1] port trunk permit vlan 10 20

[DeviceB-GigabitEthernet1/0/1] qos trust dot1p

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды