H3C S5500-SI Series Скачать руководство пользователя

Страница: 86 / 130

5-25

[DeviceD] interface gigabitethernet 1/0/1

[DeviceD-GigabitEthernet1/0/1] undo link-delay

[DeviceD-GigabitEthernet1/0/1] undo stp enable

[DeviceD-GigabitEthernet1/0/1] port link-type trunk

[DeviceD-GigabitEthernet1/0/1] port trunk permit vlan all

[DeviceD-GigabitEthernet1/0/1] qos trust dot1p

[DeviceD-GigabitEthernet1/0/1] quit

[DeviceD] interface gigabitethernet 1/0/2

[DeviceD-GigabitEthernet1/0/2] undo link-delay

[DeviceD-GigabitEthernet1/0/2] undo stp enable

[DeviceD-GigabitEthernet1/0/2] port link-type trunk

[DeviceD-GigabitEthernet1/0/2] port trunk permit vlan all

[DeviceD-GigabitEthernet1/0/2] qos trust dot1p

[DeviceD-GigabitEthernet1/0/2] quit

# Create RRPP domain 1, configure VLAN 4092 as the primary control VLAN of RRPP domain 1,

and configure VLANs mapped to MSTIs 0 through 16 as the protected VLANs of RRPP domain

[DeviceD] rrpp domain 1

[DeviceD-rrpp-domain1] control-vlan 4092

[DeviceD-rrpp-domain1] protected-vlan reference-instance 0 to 16

# Configure Device D as the transit node of primary ring 1, with GigabitEthernet 1/0/1 as the

primary port and GigabitEthernet 1/0/2 as the secondary port, and enable ring 1.

[DeviceD-rrpp-domain1] ring 1 node-mode transit primary-port gigabitethernet 1/0/1

secondary-port gigabitethernet 1/0/2 level 0

[DeviceD-rrpp-domain1] ring 1 enable

[DeviceD-rrpp-domain1] quit

# Enable RRPP.

[DeviceD] rrpp enable

5) Configuration on Device E

# Disable physical state change suppression and STP on GigabitEthernet 1/0/1 and

GigabitEthernet 1/0/2, configure the two ports as trunk ports, and assign them to all VLANs, and

configure them to trust the 802.1p precedence of the received packets.

<DeviceE> system-view

[DeviceE] interface gigabitethernet 1/0/1

[DeviceE-GigabitEthernet1/0/1] undo link-delay

[DeviceE-GigabitEthernet1/0/1] undo stp enable

[DeviceE-GigabitEthernet1/0/1] port link-type trunk

[DeviceE-GigabitEthernet1/0/1] port trunk permit vlan all

[DeviceE-GigabitEthernet1/0/1] qos trust dot1p

[DeviceE-GigabitEthernet1/0/1] quit

[DeviceE] interface gigabitethernet 1/0/2

[DeviceE-GigabitEthernet1/0/2] undo link-delay

[DeviceE-GigabitEthernet1/0/2] undo stp enable

[DeviceE-GigabitEthernet1/0/2] port link-type trunk

[DeviceE-GigabitEthernet1/0/2] port trunk permit vlan all

[DeviceE-GigabitEthernet1/0/2] qos trust dot1p

[DeviceE-GigabitEthernet1/0/2] quit

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды