H3C S5500-SI Series Скачать руководство пользователя

Страница: 117 / 130

7-5

[DeviceC-GigabitEthernet1/0/1] quit

[DeviceC] interface gigabitethernet 1/0/2

[DeviceC-GigabitEthernet1/0/2] undo stp enable

[DeviceC-GigabitEthernet1/0/2] port link-type trunk

[DeviceC-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30

[DeviceC-GigabitEthernet1/0/2] quit

# Create smart link group 1, and configure all the VLANs mapped to MSTI 1 as the protected VLANs

for smart link group 1.

[DeviceC] smart-link group 1

[DeviceC-smlk-group1]

protected-vlan reference-instance 1

# Configure GigabitEthernet 1/0/1 as the master port and GigabitEthernet 1/0/2 as the slave port for

smart link group 1.

[DeviceC-smlk-group1] port gigabitethernet 1/0/1 master

[DeviceC-smlk-group1] port gigabitethernet 1/0/2 slave

# Enable the smart link group to transmit flush messages.

[DeviceC-smlk-group1] flush enable

[DeviceC-smlk-group1] quit

2) Configuration on Device A

# Create VLANs 1 through 30.

<DeviceA> system-view

[DeviceA] vlan 1 to 30

# Configure GigabitEthernet 1/0/1 and GigabitEthernet 1/0/2 as trunk ports, assign them to VLANs 1

through 30, and enable flush message receiving on them.

[DeviceA] interface gigabitethernet 1/0/1

[DeviceA-GigabitEthernet1/0/1] port link-type trunk

[DeviceA-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30

[DeviceA-GigabitEthernet1/0/1] smart-link flush enable

[DeviceA-GigabitEthernet1/0/1] quit

[DeviceA] interface gigabitethernet 1/0/2

[DeviceA-GigabitEthernet1/0/2] port link-type trunk

[DeviceA-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30

[DeviceA-GigabitEthernet1/0/2] smart-link flush enable

[DeviceA-GigabitEthernet1/0/2] quit

3) Configuration on Device B

# Create VLANs 1 through 30.

<DeviceB> system-view

[DeviceB] vlan 1 to 30

# Configure GigabitEthernet 1/0/1 and GigabitEthernet 1/0/2 as trunk ports, assign them to VLANs 1

through 30, and enable flush message receiving on them.

[DeviceB] interface gigabitethernet 1/0/1

[DeviceB-GigabitEthernet1/0/1] port link-type trunk

[DeviceB-GigabitEthernet1/0/1] port trunk permit vlan 1 to 30

[DeviceB-GigabitEthernet1/0/1] smart-link flush enable

[DeviceB-GigabitEthernet1/0/1] quit

[DeviceB] interface gigabitethernet 1/0/2

[DeviceB-GigabitEthernet1/0/2] port link-type trunk

[DeviceB-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30

[DeviceB-GigabitEthernet1/0/2] smart-link flush enable

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды