H3C S5500-SI Series Скачать руководство пользователя

Страница: 59 / 130

4-19

2) Configuration on Device B

# Enable DLDP globally, configure GigabitEthernet 1/0/50 and GigabitEthernet 1/0/51 to operate in full

duplex mode, and then enable DLDP on the two ports.

<DeviceB> system-view

[DeviceB] dldp enable

[DeviceB] interface gigabitethernet 1/0/50

[DeviceB-GigabitEthernet1/0/50] duplex full

[DeviceB-GigabitEthernet1/0/50] speed 1000

[DeviceB-GigabitEthernet1/0/50] dldp enable

[DeviceB-GigabitEthernet1/0/50] quit

[DeviceB] interface gigabitethernet 1/0/51

[DeviceB-GigabitEthernet1/0/51] duplex full

[DeviceB-GigabitEthernet1/0/51] speed 1000

[DeviceB-GigabitEthernet1/0/51] dldp enable

[DeviceB-GigabitEthernet1/0/51] quit

# Set the DLDP mode to enhanced.

[DeviceB] dldp work-mode enhance

# Set the port shutdown mode to manual.

[DeviceB] dldp unidirectional-shutdown manual

3) Verifying the configurations

After the configurations are complete, you can use the

display dldp

command to display the DLDP

configuration information on ports.

# Display the DLDP configuration information on all the DLDP-enabled ports of Device A.

[DeviceA] display dldp

DLDP global status : enable

DLDP interval : 5s

DLDP work-mode : enhance

DLDP authentication-mode : none

DLDP unidirectional-shutdown : manual

DLDP delaydown-timer : 1s

The number of enabled ports is 2.

Interface GigabitEthernet1/0/50

DLDP port state : advertisement

DLDP link state : up

The neighbor number of the port is 1.

Neighbor mac address : 0023-8956-3600

Neighbor port index : 59

Neighbor state : two way

Neighbor aged time : 11

Interface GigabitEthernet1/0/51

DLDP port state : advertisement

DLDP link state : up

The neighbor number of the port is 1.

Neighbor mac address : 0023-8956-3600

Neighbor port index : 60

Neighbor state : two way

Neighbor aged time : 12

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды