H3C S5500-SI Series Скачать руководство пользователя

Страница: 39 / 130

3-14

[DeviceD-GigabitEthernet1/0/3] cfd remote-mep 1001 service-instance 1 mep 4002

[DeviceD-GigabitEthernet1/0/3] cfd remote-mep 5001 service-instance 1 mep 4002

[DeviceD-GigabitEthernet1/0/3] cfd mep service-instance 1 mep 4002 enable

[DeviceD-GigabitEthernet1/0/3] cfd cc service-instance 1 mep 4002 enable

4) On Device E

<DeviceE> system-view

[DeviceE] interface gigabitethernet 1/0/4

[DeviceE-GigabitEthernet1/0/4] cfd mep 5001 service-instance 1 inbound

[DeviceE-GigabitEthernet1/0/4] cfd remote-mep 1001 service-instance 1 mep 5001

[DeviceE-GigabitEthernet1/0/4] cfd remote-mep 4002 service-instance 1 mep 5001

[DeviceE-GigabitEthernet1/0/4] cfd mep service-instance 1 mep 5001 enable

[DeviceE-GigabitEthernet1/0/4] cfd cc service-instance 1 mep 5001 enable

After the above configuration, you can use the commands

display cfd mp

and

display cfd mep

verify your configuration.

Configuring the Rules for Generating MIPs

Network requirements

After finishing MEP configuration, you can continue to configure the MIPs.

MIPs, which are generated by some rules, are configured in the following way:

Decide the device on which MIPs are to be configured.

Choose suitable rules for MIP generation. By default, MIP is not configured on a device. If MIPs

are to be configured on each port in the MD, you should choose the

default

rule. If MIPs are to be

configured only when the low level MDs having MEP, you should choose the

explicit

rule.

According to the diagram as shown in

Figure 3-8

, perform the following configurations:

In MD_A, Device B is designed to have MIPs when its port is configured with low level MEPs. In

this case, port GigabitEthernet 1/0/3 is configured with MEPs of MD_B, and the MIPs of MD_A

can be configured on this port. Based on the design, you should configure the MIP generation rule

of MD_A to explicit on Device B.

The MIPs of MD_B are designed on Device C, and are configured on all ports. Based on this

design, the MIP generation rule should be configured as default.

Figure 3-8

Network diagram of MD and MP configuration

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды