H3C S5500-SI Series Скачать руководство пользователя

Страница: 88 / 130

5-27

Figure 5-10

Network diagram for intersecting-ring load balancing configuration

Configuration procedure

1) Configuration on Device A

# Create VLANs 10 and 20, map VLAN 10 to MSTI 1 and VLAN 20 to MSTI 2, and activate MST

region configuration.

<DeviceA> system-view

[DeviceA] vlan 10

[DeviceA-vlan10] quit

[DeviceA] vlan 20

[DeviceA-vlan20] quit

[DeviceA] stp region-configuration

[DeviceA-mst-region] instance 1 vlan 10

[DeviceA-mst-region] instance 2 vlan 20

[DeviceA-mst-region] active region-configuration

[DeviceA-mst-region] quit

# Disable physical state change suppression and STP on GigabitEthernet 1/0/1 and

GigabitEthernet 1/0/2, configure the two ports as trunk ports, and assign them to VLAN 10 and

VLAN 20, and configure them to trust the 802.1p precedence of the received packets.

[DeviceA] interface gigabitethernet 1/0/1

[DeviceA-GigabitEthernet1/0/1] undo link-delay

[DeviceA-GigabitEthernet1/0/1] undo stp enable

[DeviceA-GigabitEthernet1/0/1] port link-type trunk

[DeviceA-GigabitEthernet1/0/1] port trunk permit vlan 10 20

[DeviceA-GigabitEthernet1/0/1] qos trust dot1p

[DeviceA-GigabitEthernet1/0/1] quit

[DeviceA] interface gigabitethernet 1/0/2

[DeviceA-GigabitEthernet1/0/2] undo link-delay

[DeviceA-GigabitEthernet1/0/2] undo stp enable

[DeviceA-GigabitEthernet1/0/2] port link-type trunk

[DeviceA-GigabitEthernet1/0/2] port trunk permit vlan 10 20

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды