H3C S5500-SI Series Скачать руководство пользователя

Страница: 58 / 130

4-18

Make configuration so that DLDP, upon detecting a unidirectional link, reminds the network

administrator to manually shut down the faulty port.

Figure 4-4

Network diagram for configuring manual shutdown of unidirectional links

Correct fiber connection

Fiber link

Cross-connected fibers

Device A

Device B

Device A

Device B

Ethernet

optical port

Tx end

Rx end

GE1/0/50

GE1/0/51

GE1/0/50

GE1/0/51

GE1/0/50

GE1/0/51

GE1/0/50

GE1/0/51

Configuration procedure

1) Configuration on Device A

# Enable DLDP globally.

<DeviceA> system-view

[DeviceA] dldp enable

# Configure GigabitEthernet 1/0/50 to operate in full duplex mode, configure the port rate as 1000

Mbps, and enable DLDP on the port.

[DeviceA] interface gigabitethernet 1/0/50

[DeviceA-GigabitEthernet1/0/50] duplex full

[DeviceA-GigabitEthernet1/0/50] speed 1000

[DeviceA-GigabitEthernet1/0/50] dldp enable

[DeviceA-GigabitEthernet1/0/50] quit

# Configure GigabitEthernet 1/0/51 to operate in full duplex mode, configure the port rate as 1000

Mbps, and enable DLDP on the port.

[DeviceA] interface gigabitethernet 1/0/51

[DeviceA-GigabitEthernet1/0/51] duplex full

[DeviceA-GigabitEthernet1/0/51] speed 1000

[DeviceA-GigabitEthernet1/0/51] dldp enable

[DeviceA-GigabitEthernet1/0/51] quit

# Set the DLDP mode to enhanced.

[DeviceA] dldp work-mode enhance

# Set the port shutdown mode to manual.

[DeviceA] dldp unidirectional-shutdown manual

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды