H3C S5500-SI Series Скачать руководство пользователя

Страница: 108 / 130

6-47

[DeviceA] interface gigabitethernet 1/0/2

[DeviceA-GigabitEthernet1/0/2] port link-type trunk

[DeviceA-GigabitEthernet1/0/2] port trunk permit vlan 1 to 30

[DeviceA-GigabitEthernet1/0/2] smart-link flush enable

[DeviceA-GigabitEthernet1/0/2] quit

6) Verifying the configurations

You can use the

display smart-link group

command to display the smart link group configuration on

each device. For example:

# Display the smart link group configuration on Device C.

[DeviceC] display smart-link group 1

Smart link group 1 information:

Device ID: 000f-e23d-5af0

Preemption mode: NONE

Preemption delay: 1(s)

Control VLAN: 1

Protected VLAN: Reference Instance 1

Member Role State Flush-count Last-flush-time

-------------------------------------------------------------------------------

GigabitEthernet1/0/1 MASTER ACTVIE 5 16:37:20 2009/02/21

GigabitEthernet1/0/2 SLAVE STANDBY 1 17:45:20 2009/02/21

You can use the

display smart-link flush

command to display the flush messages received on each

device. For example:

# Display the flush messages received on Device B.

[DeviceB] display smart-link flush

Received flush packets : 5

Receiving interface of the last flush packet : GigabitEthernet1/0/3

Receiving time of the last flush packet : 16:25:21 2009/02/21

Device ID of the last flush packet : 000f-e23d-5af0

Control VLAN of the last flush packet : 1

Multiple Smart Link Groups Load Sharing Configuration Example

Network requirements

As shown in

Figure 6-3

Device C is a smart link device, and Device A, Device B, and Device D are associated devices.

Traffic of VLANs 1 through 200 on Device C are dually uplinked to Device A by Device B and

Device D.

Implement dual uplink backup and load sharing on Device C: traffic of VLANs 1 through 100 is

uplinked to Device A by Device B; traffic of VLANs 101 through 200 is uplinked to Device A by

Device D.

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды