H3C S5500-SI Series Скачать руководство пользователя

Страница: 109 / 130

6-48

Figure 6-3

Network diagram for multiple smart link groups load sharing configuration

Configuration procedure

1) Configuration on Device C

# Create VLAN 1 through VLAN 200, map VLANs 1 through 100 to MSTI 1, and VLANs 101 through

200 to MSTI 2, and activate MST region configuration.

<DeviceC> system-view

[DeviceC] vlan 1 to 200

[DeviceC] stp region-configuration

[DeviceC-mst-region] instance 1 vlan 1 to 100

[DeviceC-mst-region] instance 2 vlan 101 to 200

[DeviceC-mst-region] active region-configuration

[DeviceC-mst-region] quit

# Disable STP on GigabitEthernet 1/0/1 and GigabitEthernet 1/0/2 separately, configure the ports as

trunk ports, and assign them to VLAN 1 through VLAN 200.

[DeviceC] interface gigabitethernet 1/0/1

[DeviceC-GigabitEthernet1/0/1] undo stp enable

[DeviceC-GigabitEthernet1/0/1] port link-type trunk

[DeviceC-GigabitEthernet1/0/1] port trunk permit vlan 1 to 200

[DeviceC-GigabitEthernet1/0/1] quit

[DeviceC] interface gigabitethernet 1/0/2

[DeviceC-GigabitEthernet1/0/2] undo stp enable

[DeviceC-GigabitEthernet1/0/2] port link-type trunk

[DeviceC-GigabitEthernet1/0/2] port trunk permit vlan 1 to 200

[DeviceC-GigabitEthernet1/0/2] quit

# Create smart link group 1, and configure all VLANs mapped to MSTI 1 as the protected VLANs for

smart link group 1.

[DeviceC] smart-link group 1

[DeviceC-smlk-group1] protected-vlan reference-instance 1

# Configure GigabitEthernet 1/0/1 as the master port and GigabitEthernet 1/0/2 as the slave port for

smart link group 1.

[DeviceC-smlk-group1] port gigabitethernet 1/0/1 master

[DeviceC-smlk-group1] port gigabitethernet 1/0/2 slave

# Enable role preemption in smart link group 1, enable flush message sending, and configure VLAN

10 as the transmit control VLAN.

[DeviceC-smlk-group1] preemption mode role

Содержание S5500-SI Series



































































































































Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды

H3C S5500-SI Series, Руководство по настройке

Результаты поиска

Содержание S5500-SI Series

Отзывы:

Похожие инструкции для S5500-SI Series

Бренды по названию

Популярные бренды