H3C H3C S3100 8C SI Скачать руководство пользователя страница 581

Страница: 581 / 944

Operation Manual – Stack-Cluster
H3C S3100 Series Ethernet Switches

Chapter 1 Stack

1-3

Make sure the IP addresses in the IP address pool of a stack are successive so

that they can be assigned successively. For example, the IP addresses in an IP

address pool with its start IP address something like 223.255.255.254 are not

successive. In this case, errors may occur when adding a switch to the stack.

IP addresses in the IP address pool of a stack must be of the same network

segment. For example, the 1.1.255.254 is not a qualified start address for a stack

IP address pool.

If the IP address of the management VLAN interface of the main switch (or a slave

switch) is not of the same network segment as that of the stack address pool, the

main switch (or the slave switch) automatically removes the existing IP address

and picks a new one from the stack address pool as its IP address.

Since both stack and cluster use the management VLAN and only one VLAN

interface is available on the S3100 switch, stack and cluster must share the same

management VLAN if you want to configure stack within a cluster.

1.2.2 Maintaining Slave Switches

After creating a stack, you can switch to slave switch view from the main switch to

configure slave switches.

Operation

Command

Description

Switch to slave
switch view

stacking

number

Required

Number

: Serial number of the slave

switch to be accessed.

You can switch from the user view of the
main switch to that of the slave switch
without changing the user level.

You can quit slave switch view after slave switch configuration.

Operation

Command

Description

Quit slave switch view

quit

You can quit slave switch view only
by executing this command in user
view of a slave switch.

1.2.3 Stack-Port Function Configuration

I. Introduction to the Stack-Port Function

If you enable the stack function on a stack-supporting device, the device will send

join-in requests to the connected stack ports of all the switches connected with the

device. This may cause switches not expecting to join in the stack to join in the stack

automatically, affecting network stability.

Содержание H3C S3100 8C SI

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание H3C S3100 8C SI

Отзывы:

Похожие инструкции для H3C S3100 8C SI

Бренды по названию

Популярные бренды

H3C H3C S3100 8C SI, Руководство по эксплуатации

Результаты поиска

Содержание H3C S3100 8C SI

Отзывы:

Похожие инструкции для H3C S3100 8C SI

Бренды по названию

Популярные бренды