H3C H3C S3100 8C SI Скачать руководство пользователя страница 523

Страница: 523 / 944

Operation Manual – QoS-QoS Profile
H3C S3100 Series Ethernet Switches

Chapter 1 QoS Configuration

1-4

Category

Features

Refer to…

QoS actions directly
configured as required:

Priority trust mode

Traffic shaping

Line rate

Burst

For information
about priority trust
mode, refer to

Priority trust mode

For information
about traffic
shaping, refer to

Traffic Policing
and Traffic
Shaping

For information
about line rate,
refer to

Port Rate

Limiting

For information
about the burst
function, refer to

Burst

Congestion management

SP, WRR, and HQ-WRR
queue scheduling algorithms

For introduction to
SP, WRR, and
HQ-WRR queue
scheduling
algorithms, refer to

Queue Scheduling

1.3 Introduction to QoS Features

1.3.1 Traffic Classification

Traffic here refers to service traffic; that is, all the packets passing the switch.

Traffic classification means identifying packets that conform to certain characteristics

according to certain rules. It is the foundation for providing differentiated services.

In traffic classification, the priority bit in the type of service (ToS) field in IP packet

header can be used to identify packets of different priorities. The network administrator

can also define traffic classification policies to identify packets by the combination of

source address, destination address, MAC address, IP protocol or the port number of

an application. Normally, traffic classification is done by checking the information

carried in packet header. Packet payload is rarely adopted for traffic classification. The

identifying rule is unlimited in range. It can be a quintuplet consisting of source address,

source port number, protocol number, destination address, and destination port number.

It can also be simply a network segment.

Содержание H3C S3100 8C SI

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание H3C S3100 8C SI

Отзывы:

Похожие инструкции для H3C S3100 8C SI

Бренды по названию

Популярные бренды

H3C H3C S3100 8C SI, Руководство по эксплуатации

Результаты поиска

Содержание H3C S3100 8C SI

Отзывы:

Похожие инструкции для H3C S3100 8C SI

Бренды по названию

Популярные бренды