H3C H3C S3100 8C SI Скачать руководство пользователя страница 756

Страница: 756 / 944

Operation Manual – FTP-SFTP-TFTP
H3C S3100 Series Ethernet Switches

Chapter 2 TFTP Configuration

2-1

Chapter 2 TFTP Configuration

2.1 Introduction to TFTP

Compared with FTP, TFTP (trivial file transfer protocol) features simple interactive

access interface and no authentication control. Therefore, TFTP is applicable in the

networks where client-server interactions are relatively simple. TFTP is implemented

based on UDP. It transfers data through UDP port 69. Basic TFTP operations are

described in RFC 1986.

TFTP transmission is initiated by clients, as described in the following:

To download a file, a client sends Read Request packets to the TFTP server, then

receives data from the TFTP server, and sends acknowledgement packets to the

TFTP server.

To upload a file, a client sends Write Request packets to the TFTP server, then

sends data to the TFTP server, and receives acknowledgement packets from the

TFTP server.

An H3C S3100 series Ethernet switch can act as a TFTP client only.

When an S3100 series Ethernet switch serving as a TFTP client downloads files from

When you download a file that is larger than the free space of the switch’s flash

memory:

If the TFTP server supports file size negotiation, file size negotiation will be

initiated between the switch and the server and the file download operation will be

aborted if the free space of the switch’s flash memory is found to be insufficient.

If the TFTP server does not support file size negotiation, the switch will receive

data from the server until the flash memory is full. If there is more data to be

downloaded, the switch will prompt that the space is insufficient and delete the

data partially downloaded. File download fails.

TFTP-based file transmission can be performed in the following modes:

Binary mode for program file transfer.

ASCII mode for text file transfer.

Note:

Before performing TFTP-related configurations, you need to configure IP addresses for

the TFTP client and the TFTP server, and make sure a route exists between the two.

Содержание H3C S3100 8C SI

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание H3C S3100 8C SI

Отзывы:

Похожие инструкции для H3C S3100 8C SI

Бренды по названию

Популярные бренды

H3C H3C S3100 8C SI, Руководство по эксплуатации

Результаты поиска

Содержание H3C S3100 8C SI

Отзывы:

Похожие инструкции для H3C S3100 8C SI

Бренды по названию

Популярные бренды