H3C H3C S3100 8C SI Скачать руководство пользователя страница 182

Страница: 182 / 944

Operation Manual – Link Aggregation
H3C S3100 Series Ethernet Switches

Chapter 1 Link Aggregation Configuration

1-4

The system sets the ports with basic port configuration different from that of the

master port to unselected state.

There is a limit on the number of selected ports in an aggregation group. Therefore,

if the number of the selected ports in an aggregation group exceeds the maximum

number supported by the device, those with lower port numbers operate as the

selected ports, and others as unselected ports.

1.2.3 Dynamic LACP Aggregation Group

I. Introduction to dynamic LACP aggregation group

A dynamic LACP aggregation group is automatically created and removed by the

system. Users cannot add/remove ports to/from it. Ports can be aggregated into a

dynamic aggregation group only when they are connected to the same peer device and

have the same speed, duplex mode, and basic configurations, and so are/do their peer

ports.

Besides multiple-port aggregation groups, the system is also able to create single-port

aggregation groups, each of which contains only one port. LACP is enabled on the

member ports of dynamic aggregation groups.

II. Port status of dynamic aggregation group

A port in a dynamic aggregation group can be in one of the two states: selected and

unselected.

Both the selected and the unselected ports can receive/transmit LACP protocol

packets;

The selected ports can receive/transmit user service packets, but the unselected

ports cannot.

In a dynamic aggregation group, the selected port with the smallest port number

serves as the master port of the group, and other selected ports serve as member

ports of the group.

There is a limit on the number of selected ports in an aggregation group. Therefore, if

the number of the member ports that can be set as selected ports in an aggregation

group exceeds the maximum number supported by the device, the system will

negotiate with its peer end, to determine the states of the member ports according to

the port IDs of the preferred device (that is, the device with smaller system ID). The

following is the negotiation procedure:

1) Compare device IDs (system pr system MAC address) between the two

parties. First compare the two system priorities, then the two system MAC

addresses if the system priorities are equal. The device with smaller device ID will

be considered as the preferred one.

2) Compare port IDs (port pr port number) on the preferred device. The

comparison between two port IDs is as follows: First compare the two port

Содержание H3C S3100 8C SI

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание H3C S3100 8C SI

Отзывы:

Похожие инструкции для H3C S3100 8C SI

Бренды по названию

Популярные бренды

H3C H3C S3100 8C SI, Руководство по эксплуатации

Результаты поиска

Содержание H3C S3100 8C SI

Отзывы:

Похожие инструкции для H3C S3100 8C SI

Бренды по названию

Популярные бренды