H3C H3C S3100 8C SI Скачать руководство пользователя страница 100

Страница: 100 / 944

Operation Manual – VLAN
H3C S3100 Series Ethernet Switches

Chapter 1 VLAN Overview

1-1

Chapter 1 VLAN Overview

This chapter covers these topics:

VLAN Overview

Port-Based VLAN

Protocol-Based VLAN

1.1 VLAN Overview

1.1.1 Introduction to VLAN

The traditional Ethernet is a broadcast network, where all hosts are in the same

broadcast domain and connected with each other through hubs or switches. Hubs and

switches, which are the basic network connection devices, have limited forwarding

functions.

A hub is a physical layer device without the switching function, so it forwards the

received packet to all ports except the inbound port of the packet.

A switch is a link layer device which can forward a packet according to the MAC

address of the packet. However, when the switch receives a broadcast packet or

an unknown unicast packet whose MAC address is not included in the MAC

address table of the switch, it will forward the packet to all the ports except the

inbound port of the packet.

The above scenarios could result in the following network problems.

Large quantity of broadcast packets or unknown unicast packets may exist in a

network, wasting network resources.

A host in the network receives a lot of packets whose destination is not the host

itself, causing potential serious security problems.

Isolating broadcast domains is the solution for the above problems. The traditional way

is to use routers, which forward packets according to the destination IP address and

does not forward broadcast packets in the link layer. However, routers are expensive

and provide few ports, so they cannot split the network efficiently. Therefore, using

routers to isolate broadcast domains has many limitations.

The Virtual Local Area Network (VLAN) technology is developed for switches to control

broadcasts in LANs.

A VLAN can span multiple physical spaces. This enables hosts in a VLAN to be located

in different physical locations.

By creating VLANs in a physical LAN, you can divide the LAN into multiple logical LANs,

each of which has a broadcast domain of its own. Hosts in the same VLAN

communicate in the traditional Ethernet way. However, hosts in different VLANs cannot

Содержание H3C S3100 8C SI

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание H3C S3100 8C SI

Отзывы:

Похожие инструкции для H3C S3100 8C SI

Бренды по названию

Популярные бренды

H3C H3C S3100 8C SI, Руководство по эксплуатации

Результаты поиска

Содержание H3C S3100 8C SI

Отзывы:

Похожие инструкции для H3C S3100 8C SI

Бренды по названию

Популярные бренды