GSi Smart Climate 310 Скачать руководство пользователя страница 91

Страница: 91 / 102

Smart Climate 310 rev. 03 91

Updating the Software Using a USB drive

The USB drive allows upgrading the firmware or software of your

controller. It can also be used to make a backup of your controller

settings or to copy these settings on another controller of the same

type.

Turn off power each time you open the controller’s enclosure.

This prevents accidental exposure to areas of high voltage.

1.  Power off the controller.
2.  Lift the latch to open the front door of the controller.
3.  Insert the USB drive in the connector behind the front door.

4. Close the front cover and reapply power to the controller.
5. Simultaneously press and hold the

Current Conditions

up- and down-arrow keys for 5 seconds to display the

transfer menu.

Содержание Smart Climate 310







































































































Результаты поиска

Содержание Smart Climate 310

Отзывы:

Бренды по названию

Популярные бренды

GSi Smart Climate 310, Руководство пользователя

Результаты поиска

Содержание Smart Climate 310

Отзывы:

Бренды по названию

Популярные бренды