GSi Smart Climate 310 Скачать руководство пользователя страница 51

Страница: 51 / 102

Smart Climate 310 rev. 03 51

Setting Timer 1 & 2 Time On and Time Off

The On and Off times of both mist timers can be adjusted from 0 to

60 minutes.

1. Press

Mist

Accessible if mist units are enabled in the USER SETUP.

2. Press the down-arrow key twice. The On and Off times

of the first mist timer are displayed.

3. Press

Adjust

. The on time flashes on the display.

4. Use the arrow keys to set it to the desired value.
5. Press

Adjust

. The off time flashes on the display.

6. Use the arrow keys to set it to the desired value.
7. Press

Adjust

to validate the value.

8. Press the down-arrow key three times. The On and off

times of the second mist timer are displayed.

9. Press

Adjust

. The on time of the second mist timer

flashes on the display.

10. Use the arrow keys to set it to the desired value.
11. Press

Adjust

. The off time of the second mist timer

flashes on the display.

12. Use the arrow keys to it to the desired value.
13. Press

Adjust

to validate the value.

Содержание Smart Climate 310







































































































Результаты поиска

Содержание Smart Climate 310

Отзывы:

Бренды по названию

Популярные бренды

GSi Smart Climate 310, Руководство пользователя

Результаты поиска

Содержание Smart Climate 310

Отзывы:

Бренды по названию

Популярные бренды