GSi Smart Climate 310 Скачать руководство пользователя страница 73

Страница: 73 / 102

Smart Climate 310 rev. 03 73

7. Press

Adjust

then use the arrow keys to adjust these

openings to the desired value.

8. Repeat steps 1 to 7 to set the opening of the air inlet or

chimney damper for every step.

Adjusting the Maximum Opening

This is the maximum air inlet opening that is reached beyond the

last ventilation stage.
To adjust the maximum opening, proceed as follows:

1. Select the desired air inlet: AIR INLET 1, AIR INLET 2 or

0-10v Output

(0-10V air inlet).

Note that this parameter does not apply to 0-10V chimney dampers.

2. Press the down-arrow key, in order to select

Max Opening

display.

3. Press

Adjust

then use the arrow keys to adjust the max

opening to the desired value.

4. Press

Adjust

to validate.

Adjusting the Number of Degrees to Maximum

Opening

This is the temperature interval over which the air inlet goes from

the opening associated with the last ventilation stage towards its

maximum opening (see previous graphs). This parameter can be

adjusted from 0.5 to 20°F (0.3 to 11.1°C).
To adjust the number of degrees to maximum opening, proceed as

follows:

1. Select the desired air inlet: AIR INLET 1, AIR INLET 2 or

0-10v Output

(0-10V air inlet).

Note that this parameter does not apply to 0-10V chimney dampers.

2. Press the down-arrow key, to select the

Degrees To Max

Opening

display.

3. Press

Adjust

. The number of degrees to max opening

flash on the display.

4. Use the arrow keys to set this parameter to the desired

value.

Содержание Smart Climate 310







































































































Результаты поиска

Содержание Smart Climate 310

Отзывы:

Бренды по названию

Популярные бренды

GSi Smart Climate 310, Руководство пользователя

Результаты поиска

Содержание Smart Climate 310

Отзывы:

Бренды по названию

Популярные бренды