GSi Smart Climate 310 Скачать руководство пользователя страница 15

Страница: 15 / 102

Smart Climate 310 rev. 03 15

SITE MONITORING

Viewing Heater Run Times

The controller has a history in which run times of the heating units

are logged in for the past 6 day.

1. Press

Heater Run Time

Available if at least one heating stage is enabled in the USER

SETUP.

The current run time of the first heating stage is displayed

along with the time and date.

2. Keep pressing the down-arrow key to scroll down the

display and look at the 6-day history.

Viewing Water Consumption

The controller provides a pulse input to monitor the water

consumption. The water consumption is logged into an history for

the current day and for the past 6 days.

1. Press

Water Consumption

. Today's water consumption is

displayed.

Available if the water counter is enabled in the USER SETUP.

2. Press the down-arrow key to scroll the display. The water

consumption of the past 6 days is displayed.

Содержание Smart Climate 310







































































































Результаты поиска

Содержание Smart Climate 310

Отзывы:

Бренды по названию

Популярные бренды

GSi Smart Climate 310, Руководство пользователя

Результаты поиска

Содержание Smart Climate 310

Отзывы:

Бренды по названию

Популярные бренды