GSi Smart Climate 310 Скачать руководство пользователя страница 78

Страница: 78 / 102

78 Smart Climate 310 rev. 03

Adjusting the Static Pressure Compensation Value

Select the opening that must be added or removed when a

pressure compensation is applied on an air inlet. This parameter

ranges from 0 to 10% and must be set separately for each inlet. To

deactivate an inlet, set the value to Off.
To adjust the SP compensation value, proceed as follows:

1. Select the desired air inlet:

Air Inlet 1, Air Inlet 2

0-10V

Output

(0-10V air inlet).

The following parameters do not apply to 0-10V chimney dampers.

2. Press the down-arrow key to display

the Stat. P Compens

parameter.

This parameter is accessible if the static pressure compensation

option is enabled in the USER SETUP.

3. Press

Adjust

. The compensation value flashes on the

display.

4. Use the arrow keys to set it to the desired value.

Содержание Smart Climate 310







































































































Результаты поиска

Содержание Smart Climate 310

Отзывы:

Бренды по названию

Популярные бренды

GSi Smart Climate 310, Руководство пользователя

Результаты поиска

Содержание Smart Climate 310

Отзывы:

Бренды по названию

Популярные бренды