GSi Smart Climate 310 Скачать руководство пользователя страница 74

Страница: 74 / 102

74 Smart Climate 310 rev. 03

Selecting the Maximum Opening Mode

Select the proper maximum opening method: dumping /

progressive. Refer to previous graphs.
To select the maximum opening mode, proceed as follows:

1. Select the desired air inlet: AIR INLET 1, AIR INLET 2 or

0-10v Output

(0-10V air inlet).

Note that this parameter does not apply to 0-10V chimney dampers.

2. Press the down-arrow key, in order to select

Max.

Opening Mode

display.

3. Press

Adjust

then use the arrow keys to select the proper

opening mode (dumping / progressive).

4. Press

Adjust

once again to validate.

Adjusting the Temperature Compensation and Probe

Assignment

The temperature compensation is expressed as a percentage per

degree difference between the ambient temperature and the

average reading of the inlet’s probes. For each degree above or

below the average temperature, the inlet will open or close using

the compensation value. Set this value separately for each inlet. It

ranges from OFF to 10%. To deactivate compensation, press the

down arrow until compensation value displays “Off”.
To set the temperature compensation, proceed as follows:

1. Select the desired air inlet

: Air Inlet

Air Inlet

0-10v

Output

(0-10V air inlet). The actuator's position is

displayed on screen.

Note that this parameter does not apply to 0-10V chimney dampers.

Accessible if the chosen air inlet is enabled in the User Setup menu.

2. Press the down-arrow key to display the

T°

Compensation

parameter.

3. Press

Adjust

and then set the opening compensation to

the desired value.

4. Press

Adjust

again to validate.

5. Press the down-arrow key to display the probes. The

temperature probes that are assigned to the selected inlet

are displayed.

Содержание Smart Climate 310







































































































Результаты поиска

Содержание Smart Climate 310

Отзывы:

Бренды по названию

Популярные бренды

GSi Smart Climate 310, Руководство пользователя

Результаты поиска

Содержание Smart Climate 310

Отзывы:

Бренды по названию

Популярные бренды