GSi Cumberland Hi-Lo страница 84 Скачать руководство пользователя

Страница: 84 / 104

8. Troubleshooting

PNEG-250

Hi-Lo and PRO-1 Pan Feeders

2. Spinner control pan will

not restart system when
feed is called for.
(continued)

e. Check to see if the spinner motor spins,

but the feed line motor does not come
ON and the green light does not
come ON.

e. Replace the PC board.

f. Check to see if the spinner motor does

not spin due to something lodged
between the paddle and the throat.

f. The spinner motor mounting bracket may

need to be bent to point the paddle slightly to
the center of the throat and away from the
throat wall.

3. Motor overloads.

a. Check that there is the proper supply of

power from the supply line.

a1. Use the proper line voltage.

a2. Use the proper wiring size for the motor and

the length of the line run.

b. Check to see if any object(s) are caught

in the auger.

b. Remove any obstruction(s) from the hopper,

boot and outlet holes.

c. Check to see that the auger was

properly installed.

c. Make sure the boot and control unit are

installed properly.

4. The feeders will not run.

a. Check to see if there is power in the

circuit line.

a. Replace any burned out fuse(s) and correct

any tripped circuit breaker(s).

b. Check to see if the overload was tripped

on the motor.

b. Determine the reason for the overload.

(See Motor Overloads.)

c. Check to see if the control pan switch is

defective or out of alignment.

c1. Adjust the switch.

c2. Replace the switch, if it is defective.

5. The auger runs erratically.

a. Note that a new auger will cause

excessive noise until it is polished.

a. Run feed through the feed line.

b. Check to see if there is a bad bearing in

the boot assembly.

b1. Replace the bearing, if necessary.

b2. Make sure the auger was stretched properly.

c. Check to see if the auger was

incorrectly stretched.

c. Refer to

assembly and installation section

on Page 60

of this manual.

d. Check for any obstruction(s) in

the auger.

d. Remove any obstruction(s) in the boot

and/or line.

6. The feeder is extra

noisy and/or there is
excessive wear.

a. Check to see if the auger is bent.

a. Remove the auger, find the kink and

straighten it. Refer to assembly and
installation section on

Pages 61-62

this manual.

b. Check for any bad weld(s) in the auger.

b. File any bad weld(s) smooth.

c. Check for any distortions or bends in the

auger tube.

c. Remove and replace the auger tube.

7. There is not enough feed

moving to the pans.

a. Check to see if the feed is bridged in the

hopper or the boot.

a. Install an agitator ball.

b. Check to see that the boot idler shaft is

the proper length.

b. Cut the shaft to a shorter length for more

feed. Do not shorten the shaft more than
1" (2.54 cm) from the boot sidewall.

c. Check to see if the fill system feed level

control switch is out of adjustment
or defective.

c. Adjust the feed level control switch for the

proper operation.

Problem

Checks

Corrective Action

Содержание Cumberland Hi-Lo









































































































Результаты поиска

Содержание Cumberland Hi-Lo

Отзывы:

Похожие инструкции для Cumberland Hi-Lo

Бренды по названию

Популярные бренды

GSi Cumberland Hi-Lo, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cumberland Hi-Lo

Отзывы:

Похожие инструкции для Cumberland Hi-Lo

Бренды по названию

Популярные бренды