GSi Cumberland Hi-Lo страница 60 Скачать руководство пользователя | Manualshive

Страница: 60 / 104

background image

7. Installation

60

PNEG-250

Hi-Lo and PRO-1 Pan Feeders

Auger Installation

1. Remove the bearing cap, bearing and idler shaft from the boot.

2. Remove the cover plate on the control unit.

3. Feed the auger through the boot end into the auger tube, using constant care and inspection.

Two (2) people should be used for this operation: One should feed the auger into the auger tube while
the other sees that the auger is uncoiled without creating any strain. If feeding long lengths of auger
into the auger tube, overcome resistance by rotating the auger while pushing it into the tube.

4. In the event of a bend or kink, try to straighten the auger by hand. If the auger will not straighten by

hand, use locking pliers. If the auger still cannot be straightened, cut it on both sides of the bend and
remove the bent portion. A hacksaw or bolt cutters can be used to cut the auger. Refer to the auger
brazing section to reconnect the auger.

5. Make certain that the 3/4" washer is installed on the gearbox output shaft and is located between

the gearbox face and U-bolt (A). Loosen the U-bolt on the gearbox shaft and thread the auger
through the U-bolt to within 1/2" (13 mm) of the rear drive wall as shown in

the U-bolt securely.

6. Pull the auger from the boot end until all slack is removed.

Figure 7CQ

Ref #

Description

A

U-Bolt

NOTICE

Watch carefully for wire, tags, metal clips and especially for kinks and bends. If
the auger is bent or kinked, it must be straightened prior to operation. Otherwise,
excessive auger tube wear will result.

A

«
...
58
59
60
61
62
...
»

Содержание Cumberland Hi-Lo









































































































Отзывы:

Нет отзывов

Похожие инструкции для Cumberland Hi-Lo

Бренд: ZOLL Страницы: 344

Бренд: ABB Страницы: 9

Бренд: BANLAW Страницы: 32

Бренд: Baker Instrument Company Страницы: 24

Бренд: ICS Schneider Messtechnik Страницы: 124

ImageQuant LAS 4000

Бренд: GE Страницы: 86

Бренд: GE Страницы: 160

Бренд: GE Страницы: 134

Бренд: GE Страницы: 43

Бренд: GE Страницы: 37

Бренд: GE Страницы: 210

Бренд: GE Страницы: 160

Бренд: GE Страницы: 146

Бренд: GE Страницы: 6

Бренд: GE Страницы: 27

Бренд: GE Страницы: 4

Бренд: Hanil Страницы: 60

Бренд: Harken Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды