GSi Cumberland Hi-Lo Скачать руководство пользователя

Страница: 74 / 104

7. Installation

PNEG-250

Hi-Lo and PRO-1 Pan Feeders

7. For systems shorter than 360' (109.7 m), extend the 3/16" (0.476 cm) winch cable the full length of

the feeder line, stringing the cable through the cable hole on the winch drum. Temporarily attach the
cable to the ceiling with nails, staples or some type of fastener. The winch cable does not pass
though any pulleys.

(See Figure 7DL.)

8. For systems longer than 360' (109.7 m), install the cable with double reduction pulleys as shown in

Figure 7DM

Figure 7DL

Figure 7DM

NOTE:

The distance between the winch drum and the double reduction pulleys should be slightly greater
than the distance the feed line is to be raised.

9. Attach the 1-3/4" (4.445 cm) pulley to each hook as shown in

Figure 7DN

Figure 7DN

Ref #

Description

Winch

Cable Clamp

Содержание Cumberland Hi-Lo









































































































Результаты поиска

Содержание Cumberland Hi-Lo

Отзывы:

Похожие инструкции для Cumberland Hi-Lo

Бренды по названию

Популярные бренды

GSi Cumberland Hi-Lo, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cumberland Hi-Lo

Отзывы:

Похожие инструкции для Cumberland Hi-Lo

Бренды по названию

Популярные бренды