GSi Cumberland Hi-Lo Скачать руководство пользователя

Страница: 61 / 104

7. Installation

PNEG-250

Hi-Lo and PRO-1 Pan Feeders

7. Mark the auger (B) at the edge of the boot where the bearing mounts, as shown in

Figure 7CR

Figure 7CR

8. Determine the amount of stretch required, by using the chart.

See Auger Stretch Chart.

Auger Stretch Chart

9. Pull the auger out as far as necessary, starting from the “relaxed” mark on the auger and measuring

towards the boot.

10. Mark the auger at the point which allows the proper stretch (C).

(See Figure 7CS.)

Figure 7CS

Use caution when releasing the tension on the auger. If the auger moves too quickly
in any direction, it can injure the operator.

CAUTION

Ref #

Description

Mark the auger here.

2" Pitch 0.814 I.D.

Length of System

Stretch per 100 Ft.

0-100 ft. (0-30.48 m)

7.5" (19.05 cm)

100-200 ft. (30.48-60.96 m)

8.0" (20.32 cm)

200-300 ft. (60.96-91.44 m)

9.0" (22.86 cm)

300-400 ft. (91.44-121.92 m)

10" (25.4 cm)

400-500 ft. (121.92-152.4 m)

11" (27.94 cm)

500 ft.+ (152.4 m+)

12" (30.48 cm)

Ref #

Description

Proper Stretch

Содержание Cumberland Hi-Lo









































































































Результаты поиска

Содержание Cumberland Hi-Lo

Отзывы:

Похожие инструкции для Cumberland Hi-Lo

Бренды по названию

Популярные бренды

GSi Cumberland Hi-Lo, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cumberland Hi-Lo

Отзывы:

Похожие инструкции для Cumberland Hi-Lo

Бренды по названию

Популярные бренды