manualshive.com logo in svg

GSi Cumberland Hi-Lo, Инструкция по установке и эксплуатации

Поделиться
Скачать
GSi Cumberland Hi-Lo Скачать руководство пользователя страница 75

7. Installation

PNEG-250

 Hi-Lo and PRO-1 Pan Feeders

75

10. Thread the 1/8" (0.3175 cm) drop cable through each pulley and attach it to the 3/16" (0.47625 cm) 

winch cable about 6" (15 cm) from the pulley towards the winch with the 1/8" x 3/16" (0.3175 cm x 
0.47625 cm) cable clamps. 

(See Figure 7DN on Page 74.)

11. Place the hangers to the feed line directly below each pulley by snapping the wire hanger (I) around 

the rib of the tube. 

(See Figure 7DO.)

Be sure the hangers are not touching the shocker wire.

Spread the wire hanger just enough to force it over the auger tube. The clip should be located within 
6" (15 cm) (J) above the hanger, as shown in 

Figure 7DO

. So the feeder line can be raised without 

interference when the house is cleaned.

12. Cut the drop cable long enough for installation from the winch cable, through the hanger to the cable 

adjustment clip. 

(See Figure 7DO.)

Figure 7DO 

13. Begin installing the drops at the winch and proceed to the end of the feeder line.

14. Clamp off the ends of the winch cable around a truss on the ends of the feeder line. Use a cable 

clamp sleeve to clamp the drop cable to the winch cable. Thread the drop cable through the tube 
hanger and adjustment clip. Cut the winch cable behind the cable clamp.

15. Level the feed line using the adjustment clips (H). Trim excess drop cable close to the clips. 

Keep tension on hanging cables at all times to prevent the pans from resting in the litter.

Ref #

Description

H

Cable Adjustment Clip

I

Wire Hanger

J

6" (15 cm)

Содержание Cumberland Hi-Lo









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды