GSi Cumberland Hi-Lo страница 65 Скачать руководство пользователя

Страница: 65 / 104

7. Installation

PNEG-250

Hi-Lo and PRO-1 Pan Feeders

650 Lbs. Hopper Scale

Refer to

Figure 7CY

as the scales are being assembled and installed.

1. Hang the 650# hopper scale assembly (D) with four (4) drops from the main winch cable.

2. Using the cotter pins attached to the unloader (F), assemble the unloader extension (E) to the top

of the unloader. With cables, the unloader/extension assembly can now be suspended from the
650# hopper scale assembly at the desired height.

3. Assemble the hopper hangers (B) to the hopper (A) during hopper assembly. The hangers for

120/200 lbs. hoppers and 300/400 lbs. hoppers are included with the scale. Use the correct set of
hangers for the hopper that you have.

4. Attach the scale gate (C) to the bottom of the hopper and secure into place with the supplied

cotter pins.

5. The hopper can now be placed into the scale with the notches in the hopper hanger resting on the

hopper scale bars.

Figure 7CY

Ref #

Description

Ref #

Description

Hopper

650# Hopper Scale Assembly

Hopper Hanger

Unloader Extension

Scale Gate

Unloader

Содержание Cumberland Hi-Lo









































































































Результаты поиска

Содержание Cumberland Hi-Lo

Отзывы:

Похожие инструкции для Cumberland Hi-Lo

Бренды по названию

Популярные бренды

GSi Cumberland Hi-Lo, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cumberland Hi-Lo

Отзывы:

Похожие инструкции для Cumberland Hi-Lo

Бренды по названию

Популярные бренды