GSi Cumberland Hi-Lo страница 62 Скачать руководство пользователя | Manualshive

Страница: 62 / 104

background image

7. Installation

62

PNEG-250

Hi-Lo and PRO-1 Pan Feeders

11. Pull the auger out from the back of the hopper (D) an additional 8" (20.3 cm) and clamp at that point

with a pair of locking pliers.

(See Figure 7CT.)

12. Allow the pliers to rest against the boot to hold the auger in place.

Figure 7CT

If the auger is allowed to spring back, the bearing race may crack. The auger will pull itself and the
bearing plate assembly into the correct position. Do not overtighten the U-clamp or distortion of the
auger tube may result. Rapid cooling will cause hardening and embrittlement. The auger must be
smooth to prevent feed build-up and premature tube wear.

13. Cut the auger at the mark which allowed proper stretch.

14. Leave the pliers in place against the boot.

15. Insert the idler shaft assembly into the auger and thread the auger through the U-bolt up to

1/2" (1.27 cm) from the bearing.

16. Tighten the U-bolt securely.

17. Slowly release tension on the auger.

18. Re-attach the bearing cap and the U-clamp and tighten them securely.

Figure 7CU

Ref #

Description

D

Back of Hopper

Ref #

Description

D

Back of Hopper

«
...
60
61
62
63
64
...
»

Содержание Cumberland Hi-Lo









































































































Отзывы:

Нет отзывов

Похожие инструкции для Cumberland Hi-Lo

Бренд: ABB Страницы: 18

Бренд: R-Tech Страницы: 3

Бренд: YSI Страницы: 70

Бренд: jcb Страницы: 41

medialon Showmaster Go

Бренд: 7th Sense Страницы: 9

Бренд: SAMCHULLY Страницы: 48

Бренд: HAGS Страницы: 5

Бренд: HAGER WERKEN Страницы: 2

Бренд: Yamaha Страницы: 126

DM 2000 Version 2

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 45

Бренд: Yanmar Страницы: 49

Бренд: Fagor Страницы: 12

Бренд: Baltic Страницы: 68

Бренд: H&S Страницы: 76

VIMCO Sivoia SV-CCI-GRP

Бренд: Lutron Electronics Страницы: 2

Бренд: DC Med Страницы: 2

Serious Steel 805106

Бренд: ParaBody Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды