Gree GMV-224WM/B-X Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 375

background image

GMV5 DC INVERTER VRF UNITS SERVICE MANUAL

135

C2

Communication

failure between

main control board

and inverter

compressor drive

1. The control board is powered off;
2. The compressor drive board is
powered off;
3.

The

communication

cable

between  the  control  board  and
compressor  drive  board  is  not
connected;
4.  The  compressor  drive  board's
dial switch SA201 is wrong.

1. Check the power supply of the control
board.  Replace  the  control  board  if  it
works properly;
2.  Check  the  power  supply  of  the  drive
board.  Replace  the  drive  board  if  it
works properly;
3.  Connect  the  main  board  and  drive
board using the communication cable;
4.  Adjust  the  dial  switch  of  the
compressor drive board.

P3

Compressor drive

module reset

protection

1. The compressor drive board is
faulty.

1. Replace the compressor drive board.

P5

Inverter compressor

over-current

protection

1. The drive board's IPM module is
damaged;
2. The compressor's UVW cable is
not connected properly;
3. The compressor is damaged.

1. Replace the compressor drive board;
2.  Reconnect  the  compressor's  UVW
cable;
3. Replace the compressor.

P6

Compressor drive

IPM module

protection

1. The drive board's IPM module is
damaged;
2. The compressor's UVW cable is
not connected properly;
3. The compressor is damaged.

1. Replace the compressor drive board;
2.  Reconnect  the  compressor's  UVW
cable;
3. Replace the compressor.

P7

Compressor drive

temperature sensor

fault

1. The compressor drive board is
faulty.

1. Replace the compressor drive board.

P8

Compressor drive

IPM

over-temperature

protection

1. The compressor drive board is
faulty;
2. Thermal gel is not applied evenly
on the IPM module;
3. The IPM module is not screwed
properly.

1. Replace the compressor drive board;
2. Apply thermal gel evenly on the IPM
module;
3. Screw the IPM module properly.

P9

Inverter compressor

out-of-step

protection

1. The compressor drive board is

faulty.

2. The compressor is damaged.

1. Replace

the

compressor

drive

board.

2. Replace the compressor.

PH

Compressor drive

DC bus high voltage

protection

1.  Does  the  voltage  of  the  input
power  cable  of  the  whole  system
exceed 460 V;
2.  The  compressor  drive  board  is
faulty.

1. Lower the voltage of the input power
cable to the required range;
2. Replace the compressor drive board.

PL

Compressor drive

DC bus low voltage

protection

1. Is the voltage of the input power
cable of the whole system lower
than 320 V;
2. The compressor drive board is
faulty.

1. Elevate the voltage of the input power
cable to the required range;
2. Replace the compressor drive board.

PC

Compressor drive

current check circuit

fault

1. The compressor drive board is
faulty.

1. Replace the compressor drive board.

PF

Compressor drive

recharging circuit

fault

1. Is the voltage of the input power
cable of the whole system lower
than 280 V;
2. The compressor drive board is
faulty.

1. Elevate the voltage of the input power
cable to the required range;
2. Replace the compressor drive board.

PJ

Inverter compressor

starting failure

1. The drive board is damaged;
2. The compressor's UVW cable is
not connected properly;
3. The compressor is damaged.

1. Replace the compressor drive board;
2.  Reconnect  the  compressor's  UVW
cable;
3. Replace the compressor.

C3

Communication

failure between

1. The control board is powered off;
2. The fan drive board is powered

1. Check the power supply of the control
board. Replace the control board if it

«
...
136
137
138
139
140
...
»

Содержание GMV-224WM/B-X
























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GMV-224WM/B-X

Бренд: Haier Страницы: 22

Бренд: Audi Страницы: 199

Бренд: Heat Controller Страницы: 19

Бренд: BASETech Страницы: 12

Бренд: Electro-Air Страницы: 15

Бренд: Breathing Better NZ Страницы: 10

Бренд: TCL Страницы: 32

Бренд: Argo Страницы: 92

Бренд: Zibro Страницы: 16

DOLCECLIMA COMPACT

Бренд: Olimpia splendid Страницы: 66

Бренд: Tadiran Telecom Страницы: 44

Бренд: Hisense Страницы: 17

Бренд: Klimaire Страницы: 17

Бренд: Perfect Aire Страницы: 20

Бренд: arcelik Страницы: 33

Бренд: Champion Страницы: 12

DIFFUSIONE 10.5 HP HE

Бренд: Olimpia splendid Страницы: 108

Бренд: Heiko Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды