manualshive.com logo in svg

Graco 25B127, Инструкция - Каталог запасных частей

Поделиться
Скачать
Graco 25B127 Скачать руководство пользователя страница 4

Installation 

4

3A6338F

5. Connect the CAN cable from either CAN connection 

on the CGM to port 1 or port 2 on the EFR.

6. If used, connect the Ethernet, DeviceNet, 

PROFINET, or PROFIBUS cable (FB) to the CGM 
as applicable. Connect the other end of the cable to 
the fieldbus device.

7. Reinstall the pump yoke shroud (F) and the frame 

cover (G) onto the EFR system.

8. Using token 19A534, perform the Install or Update 

Data Map procedure in the Communications 
Gateway Module, Instructions – Parts manual. See 

Related Manuals

 on page 2.

9. Perform the 

Setup

 procedure on page 5 to 

configure the fieldbus.

NOTE:

 To produce an accurate dispense, the dispense 

valve must be controlled directly by the EFR. See the 
Electric Fixed Ratio Proportioner, Setup - Operation 
manual for I/O integration of the dispense valve with the 
EFR.

NOTE:

 See 

Automation Outputs (signals from PLC 

to EFR System)

 on page 25 for information on 

triggering a dispense through the EFR using the CGM. 
To produce accurate starts/stops, it is recommended to 
use discrete I/O to trigger a dispense. See the Electric 
Fixed Ration Proportioner, Setup-Operation manual for 
instructions on I/O integration of the triggering signal.

NOTICE

Ensure the CAN cable is connected to an appropriate 
CAN connection. Failure to connect the CAN cable 
correctly can result in damage to the CGM module.

F

IG

. 5: Cable Connections

F

IG

. 6: Cable Connections

CAN

Connector 1

ti11972a

CAN 
Connector 2

ti11985a

Содержание 25B127











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды