manualshive.com logo in svg

Graco 25B127, Инструкция - Каталог запасных частей

Поделиться
Скачать
Graco 25B127 Скачать руководство пользователя страница 36

Appendix C - Sequence Step Data Exchange 

36

3A6338F

Appendix C - Sequence Step Data Exchange

The Sequence Data Exchange is a condensed structure used to read and edit a number of steps in a sequence 
across a set of bytes. If multiple steps of sequences are needed, they must be cycled through.

Below is a timing diagram showing the Sequence Step Data Exchange portion of EFR CGM Map.

NOTE:

 A 50ms delay is suggested between each CGM signal.

When utilizing the Sequence Step Data Exchange, the first element that must be passed to the EFR is the Desired 
Step of the Active Sequence. Once the EFR receives that element, the EFR will update the Sequence Step Data 
Exchange Automation Inputs Elements for the desired step. After the Sequence Step Data Exchange Automation 
Inputs Elements have been updated, the Selected Step of the Active Sequence can be used to confirm the desired 
step data has populated the Sequence Step Data Exchange Automation Inputs Elements. Once the data has been 
confirmed for the desired step, the Sequence Step Data Exchange Automation Outputs Elements can be used to 
request new values to the EFR. If the values supplied are within the operable range of the elements, the EFR will 
accept the values and reflect the new values to the corresponding elements of the Sequence Step Data Exchange 
Automation Inputs Elements.

Automation Inputs (EFR Outputs)

Selected Step of the Active Sequence 

Selected Step Amount 

Selected Step Shot Type 

Selected Step Flow Rate 

Selected Step Calibration 

Automation Outputs (EFR Inputs)

Desired Step of the Active Sequence 

Desired Step Amount 

Desired Step Shot Type 

Desired Step Flow Rate 

Desired Step Calibration 

PLC State

Reading Sequence

Editing Sequence

Key

Duration that PLC can Read the information
Duration that PLC can Edit the information

EFR Gateway Editing Sequences

Changing

Steps 

Содержание 25B127











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды