Gossen MetraWatt SECULIFE ST PRO Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 114

Gossen MetraWatt SECULIFE ST PRO Скачать руководство пользователя страница 91

GMC-I Messtechnik GmbH

91

–

Momentary line voltage at the test
instrument is outside of the permis-
sible range (110 to 120 V or 220 to
240 V) for a 10 A/25 A R

PE

mea-

surement.

➭

The 10 A/25 A R

PE

measurement

is only available when line voltage
is between 220 and 240 V at 50 or
60 Hz, or between 110 and 120 V
at 50 or 60 Hz.

➭

If you’re using the test instrument
in an electrical system which does
not lie within one of these voltage
ranges, use the 200 mA test cur-
rent in order to determine protec-
tive conductor resistance.

–

IT system option (see section
4.1.1, “Measurements in IT Sys-
tems”) is activated. An attempt has
been made to start an active leak-
age current measurement or a
measurement with reference to PE
at the mains connection end (or a
test sequence which includes such
measurements).

➭

Select measurement type “pas-
sive”.

or

➭

Conduct the desired tests in a TT/
TN system instead of an IT system
and configure the test instrument
accordingly.

or

➭

Deactivate leakage current mea-
surements in the sequence param-
eters if possible.

Connection Error at the Applied Part Connections

–

At least one of the two fuse links
for applied part connections A
through K is missing or defective.

–

Test results are invalid.

➭

Stop the test.

➭

Disconnect the test instrument
from the mains.

➭

Check the fuse links for the applied
part connections.

–

In the event that this message does not
just appear briefly, but rather persists
uninterruptedly:

At least one of the two fuse links
for applied part connections A
through K is missing or defective.

➭

Stop the test.

➭

Disconnect the test instrument
from the mains.

➭

Check the fuse links for the applied
part connections.

Error Messages

Possible Causes

Corrective Measures

«
...
89
90
91
92
93
...
»

Содержание SECULIFE ST PRO



















































































































Отзывы:

Нет отзывов