manualshive.com logo in svg

Gossen MetraWatt SECULIFE ST PRO, Руководство пользователя, Страница: 52 / 114

Поделиться
Скачать
Gossen MetraWatt SECULIFE ST PRO Скачать руководство пользователя страница 52

52

GMC-I Messtechnik GmbH

Setting Measuring Range at the Clamp and Parameters at the Test 
Instrument

* Only  with  WZ12C
** Default value

Setting Measuring Parameters for IE 

1

Measurement must be performed with mains polarity in both directions. 
The largest value is documented

Test Sequence

➭

Before conducting any leakage current measurements, make 
sure that the “Ref. voltage L-PE” and “Alt. Test Freq.” mea-
surement parameters have been correctly set in SETUP (see 
section 6.2).

➭

Set the rotary switch to the 

I

E

 position.

➭

Connect the DUT in accordance with the selected measuring 
method.

➭

Connect the applied parts.

➭

Select the measurement type: 
– By setting the parameters 
or 
– Directly via the 

Measurement Type

 key

 

➭

In the case of 

direct and differential current measurement

, 

measurement must be performed with mains plug po-
larity in both directions. Select the respective polarity 
to this end by pressing the 

NL/LN

 key. 

➭

Start the test: press the 

START

/STOP

 key. 

➭

After each reconnection to the mains, and as soon as 
the first test is started, a mains connection test is exe-
cuted.

➭

You’re prompted to connect test probe P1.
The probe fuse is tested.

➭

In the case of the direct or differential measurement type:

 

Acknowledge the warning which indicates that line 
voltage will be connected to the test socket. 

➭

Switch the device under test on.

➭

The measured values are displayed. The measured 
value recording symbol shown at the right appears. 
Each time this key is pressed, the currently displayed 
measured value is saved to buffer memory.

➭

Turn off the device under test.

➭

End the test:

 press the 

START

/STOP

 key. 

The save symbol appears (floppy disk showing the 
number of measured values stored to buffer memory) 
and prompts you to save the measured values to an ID 
number.

➭

Read the measured values and compare them with the 
table of permissible limit values.

➭

Press the 

ESC

 key in order to discard the measured 

values stored to buffer memory and acknowledge by 
pressing the key shown at the right. 

Test Sequence with AT3-IIIE Adapter

Attention!

!

Please observe the operating instructions for the AT3-IIIE 
regarding correct connection of the test adapter and the de-
vice under test, as well as peculiarities involved in the test 
sequence.

Test Instrument

Clamp

Test Instrument

Parameter:

Transformation Ratio

Transformation 

Ratio

(switch *)

Measuring 

Range

Display Range 

with Clamp

1 mV : 1 mA

WZ12C

1 mV : 1 mA

1 mA ... 

15 A

0 mA ... 300 A

100 mV : 1 mA

SECUTEST CLIP

100 mV : 1 mA

0.1 ... 

25 mA

0.00 mA ... 3.00 A

Measuring Pa-
rameter

Meaning

Measurement Type 

Suitable for 
DUT Connection via

Direct

Direct measuring method (probe 
P1, PE(TS), all APP sockets)

Test socket, 
AT16DI/AT32DI (only diff. is sen-
sible)

Differential

Measurement in accordance with 
differential current measuring 
method L/N (TS).
Probe P1 and if applicable all 
APP sockets are grounded via 
1 k

Ω

.

Test socket

Alternative

Equivalent leakage current mea-
surement with equivalent source 
between PE and L/N at the test 
socket (L/N short-circuited) and if 
applicable all APP sockets

Test socket, AT16DI/AT32DI

AT3 adapter

Feature I01: Measurement via re-
sidual current converter in the AT3 
adapter, measured via the V-
COM sockets. Probe P1 and if 
applicable all APP sockets are 
grounded via 1 k

Ω

.

AT3-IIIE, AT3-IIS, AT3-IIS32

Clamp

Feature I01: 
Measurement of device leakage 
current via current clamp sensor 
with voltage output (V-COM 
sockets), with conversion to and 
display as current values. Probe 
P1 and if applicable all APP 
sockets are grounded via 1 k

Ω

.

Permanent connection

Polarity 

1 

For direct, differential and AT3 
adapter measurement types only

L/N or N/L

Selection of polarity for mains voltage to the test socket

Clamp factor – only for clamp measurement type

1 mV : 1 mA

Transformation ratio of the 

WZ12C

 current clamp sensor. 

For setting the current clamp factor at the 

WZ12C

 clamp and the 

test instrument (see table above).

10 mV : 1 mA

100 mV : 1 mA

Transformation ratio of the 

SECUTEST CLIP

 current clamp sensor. 

For setting the current clamp factor at the test instrument.

1 V : 1 A

Содержание SECULIFE ST PRO



















































































































Отзывы:

Нет отзывов