manualshive.com logo in svg

Gossen MetraWatt SECULIFE ST PRO, Руководство пользователя, Страница: 43 / 114

Поделиться
Скачать
Gossen MetraWatt SECULIFE ST PRO Скачать руководство пользователя страница 43

GMC-I Messtechnik GmbH

43

Setting Measuring Parameters for IPE 

Note

The currently selected 

single fault

 and the 

test condition

 are 

displayed on the initial page. In order to change them, 
they have to be 

 selected and

 

set via the measuring 

parameters menu. 
Single fault exception: This can be set via the 

SFC

 direct 

selection key.

The measurements have to be conducted under all fault condi-
tions. Selection is made in the measuring parameters menu under 

Single Fault

.

Test Sequence for Direct Measuring Method

➭

Before conducting any leakage current measurements, make 
sure that the “Ref. voltage L-PE” and “Alt. Test Freq.” mea-
surement parameters have been correctly set in SETUP (see 
section 6.2).

➭

Set the rotary switch to the 

I

PE

 position.

➭

Select the 

Direct

 measurement type: 

– By setting the parameters 
or 
– Directly via the 

Measurement Type

 key

 

➭

In the case of the 

Direct

 measuring type, the 

Single Fault

 (

SFC

 key) 

and 

Test Condition

 parameters also have to be set.

➭

Connect the DUT’s mains plug (protection class I) to the test 
instrument’s test socket.

➭

Connect the applied parts.

➭

Make sure that the device under test is switched off.

➭

Start the test:

 press the 

START

/STOP

 key. 

➭

Switch the device under test on.

➭

The measurement must be performed with mains plug 
polarity in both directions by pressing the 

NL/LN

 key. 

➭

Acknowledge the warning which indicates that line 
voltage will be connected to the test socket. 

➭

Switch the device under test on.

➭

Contact all accessible conductive parts, one after the other, 
with test probe P1, which are not connected to the housing, 
as well as any output sockets for safety extra-low voltage if in-
cluded.

➭

The measured values are displayed. The measured 
value recording symbol shown at the right appears. 
Each time this key is pressed, the currently displayed 
measured value is saved to buffer memory.

➭

Turn off the device under test.

➭

End the test:

 press the 

START

/STOP

 key. 

The save symbol appears (floppy disk showing the 
number of measured values stored to buffer memory) 
and prompts you to save the measured values to an ID 
number.

➭

Read the measured values and compare them with the table 
of permissible limit values.

➭

Press the 

ESC

 key in order to discard the measured 

values stored to buffer memory and acknowledge by 
pressing the key shown at the right. 

Test Sequence with AT3-IIIE Adapter

Attention!

!

Please observe the operating instructions for the AT3-IIIE 
regarding correct connection of the test adapter and the de-
vice under test, as well as peculiarities involved in the test 
sequence.

Measuring 
Parameter

Meaning

Measurement Type 

Suitable for 
DUT Connection via

Direct

Direct earth leakage current 
measurement between 
PE(mains) and PE(TS)

Test socket, 
AT16DI/AT32DI (direct or diff.)

Differential

Earth leakage current measure-
ment in accordance with the dif-
ferential current measuring 
method L/N(TS), PE(TS) is 
grounded

Test socket

Alternative

Equivalent leakage current mea-
surement with equivalent source 
between PE and L/N at the test 
socket (L/N short-circuited)

Test socket, VL2E, AT3 adapter 
(AT3-IIIE, AT3-IIS, AT3-IIS32), 
AT16DI/AT32DI

AT3 adapter

Earth leakage current measurement 
via residual current converter in the 
AT3 adapter, measured via the V-
COM sockets.

AT3-IIIE, AT3-IIS, AT3-IIS32

Clamp

Current clamp measurement as 
earth leakage current measure-
ment for permanently connected 
devices (current clamp sensor 
with voltage output via the V-
COM sockets with conversion to 
and display as current values)

Permanent connection

TC – test conditions

None 
APP > PE: Connect APP to PE – 

all

 APP sockets are connected to PE potential when this 

option is activated.

Single fault (SFC) – only with direct measurement type

Normal state / N interrupted

Polarity 

With direct and differential mea-
surement type only

L/N or N/L

Selection of polarity for mains voltage to the test socket

Clamp factor – only for clamp measurement type

1 mV : 1 mA

Transformation ratio of the 

WZ12C

 current clamp sensor. 

For setting the current clamp factor at the 

WZ12C

 clamp and the 

test instrument (see table above).

10 mV : 1 mA

100 mV : 1 mA

Transformation ratio of the 

SECUTEST CLIP

 current clamp sensor. 

For setting the current clamp factor at the test instrument.

1 V : 1 A

Содержание SECULIFE ST PRO



















































































































Отзывы:

Нет отзывов