manualshive.com logo in svg

Gossen MetraWatt SECULIFE ST PRO, Руководство пользователя, Страница: 33 / 114

Поделиться
Скачать
Gossen MetraWatt SECULIFE ST PRO Скачать руководство пользователя страница 33

GMC-I Messtechnik GmbH

33

Setting Measuring Parameters for RPE 

1

Measurement cannot be performed with 10/25 A AC for this measure-
ment type.

2

Feature G01: This type of measurement can only be selected if a test 
current of 10 A AC has been chosen.

Entering and Deleting Offset Values

The test instrument determines protective conductor resistance 
by means of a 4-pole measurement. If measurement cables or 
extension cords are used whose ohmic resistance should be 
automatically subtracted from the measurement results, there are 
two ways to save the respective offset value in the R

PE

 switch 

position:

•

Entry via the numeric keypad

•

Acceptance of the momentary measured value by pressing the 

SET 

OFFSET

 

softkey

Proceed as follows in order to accept the measured value:

➭

Start the measurement and wait until the measured value settles in.

➭

Press the 

SET OFFSET

 key. The value is transferred to the offset 

field.

The entered or accepted offset value is permanently stored and is 
subtracted from all protective conductor resistance values mea-
sured in the future. This applies to single measurements as well 
as to measurements conducted in the AUTO switch positions. 
The 

 symbol is displayed in the header in all switch positions 

until the offset value is deleted by pressing the 

CLEAR OFFSET

 soft-

key (R

PE

 switch position).

Protective Conductor Measurement with 25 A AC (feature G02)

In accordance with IEC 60601, at least 25 A must be achieved 
with a load of 0.1

Ω

 and a maximum voltage of 0.6 V.

Continuous protective conductor resistance measurement with a 
test current of 25 A isn’t possible due to contact resistance at the 
jacks.
If the test instrument is operated at room temperature, an uninter-
rupted 

test duration of at least 15 seconds

 is possible. Under other 

conditions, maximum test duration may be shorter and/or the 
measurement may be prematurely terminated.

Attention!

!

Suitable measurement cables with a minimum wire 
cross-section of 2.5 mm must be used when measuring 
protective conductor resistances with a “25 A AC” test 
current. 
Included: suitable test probe with 

green

 strain relief 

sleeve. 
For subsequent orders, we recommend the SK2-25A 
test probe (Z746C). 
Under certain circumstances, the required standard val-
ues might not be complied with if unsuitable accessories 
are used.

Attention!

!

Measurement duration with a 25 A test current is limited 
(see technical data). 
An error message is generated if measurement duration 
is exceeded which results in a temperature increase at 
the test instrument.

Measuring 
Parameter

Meaning

Measurement Type 

Suitable for 
DUT Connection via

(passive:) PE(TS) 
– P1

Testing is conducted between the 
two protective conductor terminals: 
at the test socket and test probe 
P1.

Test socket, EL1 with DUT at test 
socket, VL2E, AT3 adapter (AT3-
IIIE, AT3-IIS, AT3-IIS32), 
AT16DI/AT32DI

Active: PE(TS) – 
P1 (TS an) 

1

Same as 

PE(TS) – P1

, but with 

line voltage to the test socket, 
200 mA AC flows immediately. 
A ramp-like, slowly rising DC test 
current flows (PRCD triggering is 
avoided) at +200 mA DC, -
200 mA DC and 

±

200 mA DC.

Test socket (for PRCDs)

PE(mains) – P1 

1

Permanently con-
nected DUTs

Testing is conducted between the 
ground terminal at the mains and 
test probe P1.

Permanent connection

PE(mains) – P1 
clamp 

2

(features G01 and I01):

Test current measurement with 
current clamp sensor

Permanent connection

P1 – P2

(feature H01): 
2-pole measurement between 
test probes 1 and 2 (see section 
6.6)

Permanent connection

IP(set)

+200 mA DC

Test current: positive direct current

-200 mA DC

Test current: negative direct current

±

200 mA (DC)

Test current: direct current whose polarity is reversed every 2 seconds

200 mA (AC)

Test current: alternating current, adjustable frequency f, see below

10 A (AC)

10 A test current (feature G01)

25 A (AC)

25 A test current (feature G02)

f – only at 200 mA (AC)

50 ... 200 Hz

Test frequency (adjustable in steps: 50, 60, 110, 150, 200 Hz)

Offset

> 0 ... < 5 

Ω

 

Zero balancing for a selected reference point.

Polarity 

Only with measurement type 
PE(TS) – P1 (TS on)

L/N or N/L

Selection of polarity for mains voltage to the test socket

Clamp factor

 

– only for clamp measurement type

1 mV : 1 mA

Transformation ratio of the 

WZ12C

 current clamp sensor. 

For setting the current clamp factor at the 

WZ12C

 clamp and the 

test instrument (see table above).

Содержание SECULIFE ST PRO



















































































































Отзывы:

Нет отзывов