Gossen MetraWatt SECULIFE ST PRO Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 114

Gossen MetraWatt SECULIFE ST PRO Скачать руководство пользователя страница 9

GMC-I Messtechnik GmbH

9

Attention!

!

Dangerous Voltage at Connections or Contacts

When conducting measurements at APP sockets, APP
sockets are connected together for the purpose of mea-
surement or grounding depending on the selected set-
tings at the test instrument, in the automatic sequences
or in the PC software.
And thus in the event of damaged DUTs or faulty con-
tacting, dangerous voltage may occur during testing at
connections or contacts at which this isn’t expected.

Opening the Instrument / Repairs

The instrument may only be opened by authorized, trained per-
sonnel in order to ensure flawless operation and to assure that the
guarantee isn’t rendered null and void.
Even original replacement parts may only be installed by autho-
rized, trained personnel.
If it can be ascertained that the instrument has been opened by
unauthorized personnel, no guarantee claims can be honored by
the manufacturer with regard to personal safety, measuring accu-
racy, compliance with applicable safety measures or any conse-
quential damages.
If the guarantee seal is damaged or removed, all guarantee claims
are rendered null and void.

Attention!

!

Before opening the housing, pull the mains plug out of
the outlet and wait for at least 5 minutes.

The test instrument may not be used:

•

If external damage is apparent,
for example if parts which conduct dangerous touch voltage
are freely accessible,
if the display is broken or defective (in which case dangerous
voltage or mains connection errors might no longer be indi-
cated)

•

If the seal or sealing lacquer has been removed as the result
of repairs or manipulation carried out by an unauthorized/non-
certified service provider

•

With damaged connection and/or measurement cables and patient
ports, e.g. interrupted insulation or kinked cable

•

If the instrument no longer functions flawlessly

•

After extraordinary stressing due to transport

In such cases, the instrument must be removed from operation
and secured against unintentional use.

Meanings of Symbols on the Instrument

The symbols on the instrument have the following meanings:

Warning regarding dangerous electrical voltage

Warning concerning a point of danger
(attention: observe documentation!)

European conformity marking

This device may not be disposed of with household
trash.
Further information regarding the WEEE mark can be
accessed on the Internet at www.gossenme-
trawatt.com by entering the search term “WEEE”.

If the guarantee seal is damaged or removed, all guar-
antee claims are rendered null and void.

Utilized Trademarks

QR Code

QR Code is a registered trademark of
DENSO WAVE INCORPORATED

The

Bluetooth

®

word mark and logo are registered

trademarks of Bluetooth SIG, Inc.

!

®

«
...
7
8
9
10
11
...
»

Содержание SECULIFE ST PRO



















































































































Отзывы:

Нет отзывов