manualshive.com logo in svg

Gossen MetraWatt SECULIFE ST PRO, Руководство пользователя, Страница: 48 / 114

Поделиться
Скачать
Gossen MetraWatt SECULIFE ST PRO Скачать руководство пользователя страница 48

48

GMC-I Messtechnik GmbH

Test Sequence for Direct and Differential Current Methods

➭

Before conducting any leakage current measurements, make 
sure that the “Ref. voltage L-PE” and “Alt. Test Freq.” mea-
surement parameters have been correctly set in SETUP (see 
section 6.2).

➭

Set the rotary switch to the 

I

T

 position.

➭

Select measurement type 

Direct

 

P1 

or 

Differential P1

: 

– By setting the parameters 
or 
– Directly via the 

Measurement Type

 key

 

➭

In the case of measurement type 

Direct P1

, the 

Single Fault

 param-

eter (

SFC

 key) must be additionally set.

➭

In the case of measurement type 

Direct P1

 or 

Permanent Connection 

P1

, the 

Test Condition

 parameter must be additionally set.

➭

In the case of 

direct and differential current measurement

, 

measurement must be performed with mains plug po-
larity in both directions. Select the respective polarity 
to this end by pressing the 

NL/LN

 key. 

➭

Connect the DUT’s mains plug (protection class II) to the test in-
strument’s test socket.

Attention!

!

Testing is conducted in the presence of line voltage. 

➭

In the case of measurement type 

Direct

 and test condition 

APP > 

PE

: Connect the applied parts.

➭

Start the test:

 press the 

START

/STOP

 key. 

➭

Acknowledge the warning which indicates that line 
voltage will be connected to the test socket. 

➭

Switch the device under test on.

➭

Contact all accessible conductive parts, one after the other, 
which are not connected to the housing with test probe P1.

➭

The measured values are displayed. The measured 
value recording symbol shown at the right appears. 
Each time this key is pressed, the currently displayed 
measured value is saved to buffer memory.

➭

Turn off the device under test.

➭

End the test:

 press the 

START

/STOP

 key. 

The save symbol appears (floppy disk showing the 
number of measured values stored to buffer memory) 
and prompts you to save the measured values to an ID 
number.

➭

Read the measured values and compare them with the 
table of permissible limit values.

➭

Press the 

ESC

 key in order to discard the measured 

values stored to buffer memory and acknowledge by 
pressing the key shown at the right. 

Test Sequence for Alternative Measuring Method

➭

Before conducting any leakage current measurements, make 
sure that the “Ref. voltage L-PE” and “Alt. Test Freq.” mea-
surement parameters have been correctly set in SETUP (see 
section 6.2).

➭

Set the rotary switch to the 

I

T

 position.

 

➭

Select measurement type 

Alternative

 

P1

 

or 

Alternative P1–P2

 (feature H01

)

: 

– By setting the parameters 
or 
– Directly via the 

Measurement Type

 key

 

➭

Connect the DUT’s mains plug (protection class II) to the test 
instrument’s test socket.

➭

Start the test:

 press the 

START

/STOP

 key. 

➭

Contact all accessible conductive parts, one after the 
other, which are not connected to the housing with 
test probe P1.

➭

The measured values are displayed. The measured 
value recording symbol shown at the right appears. 
Each time this key is pressed, the currently displayed 
measured value is saved to buffer memory.

➭

End the test:

 press the 

START

/STOP

 key. 

The save symbol appears (floppy disk showing the 
number of measured values stored to buffer memory) 
and prompts you to save the measured values to an ID 
number.

➭

Read the measured values and compare them with the 
table of permissible limit values.

➭

Press the 

ESC

 key in order to discard the measured 

values stored to buffer memory and acknowledge by 
pressing the key shown at the right. 

Maximum Permissible Limit Values for Leakage Current in mA 

Key

I

T

Touch current (leakage current from welding current)

See section 14.8 for further limit values.

Test Standard

I

C

VDE 0701-0702:2008

0.5

DIN EN 60974-4

VDE 0544-4:2009-06

10 mA

Содержание SECULIFE ST PRO



















































































































Отзывы:

Нет отзывов