Gossen MetraWatt SECULIFE ST PRO Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 114

Gossen MetraWatt SECULIFE ST PRO Скачать руководство пользователя страница 31

GMC-I Messtechnik GmbH

31

8.5

Measuring Protective Conductor Resistance – RPE

1

10/25 A RPE measurements are only possible with line voltages of 115/
230 V and line frequencies of 50/60 Hz.

2

Connection for 2

nd

test probe for 2-pole measurement (instrument with

feature H01)

3

Only instruments with feature G01

4

Can only be selected if the IP(set) parameter has been set to 200 mA.

Application, Definition, Measuring Method

Protective conductor resistance is the sum of the following resis-
tances:

•

Connector cable or device connector cable resistance

•

Contact resistance at plug and terminal connections

•

Extension cord resistance if applicable

Protection Class I Devices
–

Measurement type PE(TS) - P1 (passive)

– DUT mains plug to test socket
– Test probe P1 to P1 terminals

Schematic Diagram

Protective conductor resistance is measured between the earth-
ing contacts at the mains plug and the earthing contact con-
nected to the housing by contacting the housing with test probe
P1.

Wiring Diagram

Measurement of RPE at Single-Phase Extension Cords with EL1
–

Measurement type PE(TS) - P1 (passive)

– Extension cord plug to test socket
– EL1 to P1 terminals

Schematic Diagram

Wiring Diagram

Protection Class I Devices
Special Case: Line Voltage at Test Socket (for testing PRCDs)
–

Measurement type PE(TS) - P1 (active)

– DUT mains plug to test socket
– Test probe P1 to P1 terminals

Schematic Diagram

Protective conductor resistance is measured between the earth-
ing contacts at the mains plug and the earthing contact con-
nected to the housing by contacting the housing with test probe
P1.

Single measurements,

rotary switch level: green

Switch

Po

si

ti

o

n

Measure-
ment Type
With Mains
to Test
Socket

Measure-
ment Type
Without
Mains
to Test
Socket

Measuring Functions

R

PE

Protective conductor resistance

Ip

Test current

200 mA

10 A

1

25 A

1

R

PE

Passive:
PE(TS) - P1

•

•

•

Active:
PE(TS) - P1

4

•

PE(mains) - P1

•

•

PE(mains) - P1
clamp

3

•

P1 - P2

2

•

•

•

R

PE

«
...
29
30
31
32
33
...
»

Содержание SECULIFE ST PRO



















































































































Отзывы:

Нет отзывов