Goodman GDVC80703B, Руководство по установке

Страница: 22 / 48

22
S S
S S
S
T T T T TA R A R A R A R A RT T T T T
-----
U P U P U P U P U P
P P
P P
P
R R R R R O C E D U R E O C E D U R E O C E D U R E O C E D U R E O C E D U R E A N D A N D A N D A N D A N D
A A
A A
A
D J U D J U D J U D J U D J US T M E N T S T M E N T S T M E N T S T M E N T S T M E N T
delay period (field selectable delay OFF [90, 120, 150, 180]
plus 30-second ramp down), the circulator blower de-
energizes.
2. Remove the burner compartment door and move the
furnace gas valve manual control to the OFF position.
3. Close the manual gas shutoff valve external to the furnace.
4. Replace the burner compartment door.
G G
G G G
AS AS AS AS AS
S S
S S S
UPPLY UPPLY UPPLY UPPLY UPPLY
P P
P P P
RESSURE RESSURE RESSURE RESSURE RESSURE
M M
M M M
EASUREMENT EASUREMENT EASUREMENT EASUREMENT EASUREMENT
CAUTION
T
O PREVENT UNRELIABLE OPERATION OR EQUIPMENT DAMAGE
,
THE
INLET GAS SUPPLY PRESSURE MUST BE AS SPECIFIED ON THE UNIT
RATING PLATE WITH ALL OTHER HOUSEHOLD GAS FIRED APPLIANCES
OPERATING
.
The line pressure supplied to the gas valve must be within the
range specified below. The supply pressure can be measured at the
gas valve inlet pressure boss or at a hose fitting installed in the gas
piping drip leg. The supply pressure must be measured with the
burners operating. To measure the gas supply pressure, use the
following procedure.
INLET OUTLET
Gas Valve On/Off
Selector Switch
White-Rodgers Model 36G54 (Two-Stage)
Inlet
Pressure
Boss
Low Fire
Regulator
Adjust
Manometer
Manometer
Hose
High Fire Regulator
Adjust
Regulator
Vent
Outlet
Pressure Boss
Open to
Atmosphere
On/Off Switch
High Fire Coil
Terminal (HI)
Coaxial Coil
Terminal (M)
Common
Terminal(C)
White-Rodgers Model 36G54 Connected to Manometer
H H
H H H
ORIZONTAL ORIZONTAL
ORIZONTAL ORIZONTAL ORIZONTAL
I I I I I
NSTALLATIONS NSTALLATIONS
NSTALLATIONS NSTALLATIONS NSTALLATIONS
Filters must be installed in either the central return register or in the
return air duct work.
S SS S S
T T
T T TA R
A R
A R A R A RT
T
T T T
-----
U P U P
U P U P U P
P P P P P
R R
R R R OCEDURE
OCEDURE
OCEDURE OCEDURE OCEDURE
A A A A A
N D N D
N D N D N D
A A A A A
D J U D J U
D J U D J U D J USTMENT
STMENT
STMENT STMENT STMENT
Furnace must have a 115 VAC power supply properly connected
and grounded. Proper polarity must be maintained for correct op-
eration. In addition to the following start-up and adjustment items,
refer to further information in
Operational Checks section.
H H
H H H
EAT EAT EAT EAT EAT
A A
A A A
NTICIPATOR NTICIPATOR NTICIPATOR NTICIPATOR NTICIPATOR
S S
S S S
ETTING ETTING ETTING ETTING ETTING
The heat anticipator in the room thermostat must be correctly ad-
justed to obtain the proper number of cycles per hour and to pre-
vent “overshooting” of the setting. Set the heat anticipator setting
to 0.7 amps. Follow the thermostat manufacturer’s instructions on
how to adjust the heat anticipator setting.
F FF
F F
URNACE URNACE URNACE URNACE URNACE
O O
O O O
PERATION PERATION PERATION PERATION PERATION
Purge gas lines of air prior to startup. Be sure not purge lines into an
enclosed burner compartment.
Check for leaks using an approved chloride-free soap and water
solution, an electronic combustible gas detector, or other approved
method. Verify that all required kits (propane gas, high altitude,
etc.) have been appropriately installed.
F
URNACE
S
TARTUP
1. Close the manual gas shutoff valve external to the furnace.
2. Turn off the electrical power to the furnace.
3. Set the room thermostat to the lowest possible setting.
4. Remove the burner compartment door.
NO NO
NO NO NOTE:
TE:
TE: TE: TE: This furnace is equipped with an ignition device which
automatically lights the burner. Do not try to light the burner by
hand.
5. Move the furnace gas valve manual control to the OFF
position.
6. Wait five minutes then smell for gas. Be sure check near the
floor as some types of gas are heavier than air.
7. If you smell gas after five minutes, immediately follow the
Safety Instructions on page 2 of this manual. If you do not
smell gas after five minutes, move the furnace gas valve
manual control to the ON position.
8. Replace the burner compartment door.
9. Open the manual gas shutoff valve external to the furnace.
10. Turn on the electrical power to the furnace.
11. Adjust the thermostat to a setting above room temperature.
12. After the burners are lit, set the thermostat to desired
temperature.
F
URNACE
S
HUTDOWN
1. Set the thermostat to the lowest setting.
The integrated control will close the gas valve and extinguish
flame. Following a 15 second delay, the induced draft blower
will be de-energized. After a 120, 150, 180 or 210-second